Updated DIN rail clips (#813)

* Create readme.md

* added images

* Revert "added images"

This reverts commit 4fa4481682.

* Upload and document

* Update readme.md

* Update readme.md

* Update readme.md

* Update readme.md

* Update readme.md

* Update readme.md

* Create t-logo.png

* Update readme.md

* Update readme.md

* Update readme.md

* Update t-logo.png

* Update t-logo.png

* update

* update

* Update readme.md

* Update README.md

* Update README.md

* Update README.md

* Update README.md

* updates

* Update README.md

* Update readme.md

* Updates for pull request

* Update README.md

* Update README.md

printer_mods/README.md

@@ -373,8 +373,9 @@ like so:
 | tayto-chip | [V2.4 Skirt Switch Mod](./tayto-chip/skirt_switch_mod) | Add a ON/OFF Switch to side or front skirts| :x: | :x: | :heavy_check_mark: |:x:|
 |teookie|[AB dial indicator mount](./teookie/AB_dial_indicator_mount)|Mount for attaching standard dial indicators to AB|:x:|:heavy_check_mark:|:heavy_check_mark:|:heavy_check_mark:|
 | | [SKR Brace](./teookie/skr_brace)|Rigidize and stabilize SKR 1.4 mounts|:x:|:x:|:heavy_check_mark:|:x:|
-| TiagoBarata |[Logitech C270 Mount](./TiagoBarata/Logitech_C270_Mount)| Logitech C270 Top Center Mount |:x:|:x:|:heavy_check_mark:|:x:|:x:|
+| th0mpy | [BEEFY Din Clips](./th0mpy/beefy-din) | Two piece BEEFY Din Clips, holds stronger | :grey_question: | :grey_question: | :heavy_check_mark: | :grey_question: | :grey_question: |
 | TheSquiffy | [V0 Belts holder](./TheSquiffy/V0_Belts_holder) | V0 Belts Holder | :heavy_check_mark: | :x: | :x: | :x: | :x: |
+| TiagoBarata |[Logitech C270 Mount](./TiagoBarata/Logitech_C270_Mount)| Logitech C270 Top Center Mount |:x:|:x:|:heavy_check_mark:|:x:|:x:|
 |Tircown| [Display mount 5"](./Tircown/Display_mount_5inch) | Tiltable mount for a 5" tactile display | :x: | :x: | :heavy_check_mark: | :x: |
 | | [Raspberry in plug panel](./Tircown/Raspberry_plug_panel) | Raspberry mount vertically in the plug panel, allow easy access to ports  | :x: | :x: | :heavy_check_mark: | :x: |
 | | [DIN mount RS-15-5 PSU](./Tircown/DIN_mount_RS-15-5) | A DIN mount for the RS-15-5  | :grey_question: | :grey_question: | :heavy_check_mark: | :grey_question: |

printer_mods/th0mpy/beefy-din/readme.md

@@ -0,0 +1,38 @@
+<img src="images/t-logo.png" width="100" />
+
+# BEEFY Din
+
+I made these Din clips to replace the Voron "print in place" clips. I had issues, no matter the print settings and/or material, with the items staying in place. These clips are two parts, the main clip and moving shuttle. The only additional piece is the spring. I used yellow and blue bed springs and it clips everything very tight, but still able to remove.
+
+I would not recommend that you use brown/red or other heavier bed springs since it applies too much pressure. 
+
+## Printing
+
+Standard Voron print settings should work well, 0.4mm nozzle with 0.2mm layer height. PETG or ABS recommended. 
+
+## What to print
+You will need to print two pieces for one clip.
+
+| Filename |  Use |
+| ------------- | ------------- |
+| BEEFY_Din-PSU(50mm)-mirrored.stl | 24v PSU (mirrored) M4 screws |
+| BEEFY_Din-PSU(50mm).stl  | 24v PSU M4 screws  |
+| BEEFY_Din(55mm).stl | 5v PSU M3 screws |
+| BEEFY_Din-shuttle.stl  | Moving shuttle for all models  |
+| BEEFY_Din(standard).stl | Used for Pi and other controllers |
+
+## Assembly
+
+Assemble before installation. Insert spring into shuttle and slide into the groves in the underside of the main body. The holes may need to be drilled out a little to fit. 
+
+![](images/IMG_0992.jpeg)
+
+![](images/BEEFY_Din-PSU(50mm).png)
+
+![](images/BEEFY_Din-(55mm).png)
+
+![](images/BEEFY_Din.png)
+
+## Parts needed
+
+This is the spring kit I used. Again I'd stick to the blue or yellow springs for the best result. https://www.amazon.com/gp/product/B081DSZTV6