Tircown's repository and mods. (#286)

* Tircown's repository and mods.

Add Tircown's repository.
Add 3 mods in:
- Tiltable mount for a 5" display in skirts
- Plug panels with raspberry in vertically
- DIN bracket for the Meanwell RS-15-5 PSU

* Fix validation errors for existing mods

Fix facets reversed for:
display5inch_front_rear_skirt_a_350.stl
display5inch_front_rear_skirt_a_300.stl
display5inch_arm_b.stl

* Readme changes

Display_mount_5inch: add instructions to remove built-in support
Raspberry_plug_panel: add instructions with description of hardware

* Fix thin wall

Fix thin wall in display5inch_case.stl and display5inch_case_moretolerance.stl

Co-authored-by: KiloQubit <69389593+KiloQubit@users.noreply.github.com>

printer_mods/README.md

@@ -163,6 +163,9 @@ like so:
 | tayto-chip | [V2.4 Skirt Switch Mod](./tayto-chip/skirt_switch_mod) | Add a ON/OFF Switch to side or front skirts| :x: | :x: | :heavy_check_mark: |:x:|
 |teookie|[AB_dial_indicator_mount](./teookie/AB_dial_indicator_mount)|Mount for attaching standard dial indicators to AB|:x:|:heavy_check_mark:|:heavy_check_mark:|:heavy_check_mark:|
 | | [SKR_Brace](./teookie/skr_brace)|Rigidize and stabilize SKR 1.4 mounts|:x:|:x:|:heavy_check_mark:|:x:|
+|Tircown| [Display mount 5"](./Tircown/Display_mount_5inch) | Tiltable mount for a 5" tactile display | :x: | :x: | :heavy_check_mark: | :x: |
+| | [Raspberry in plug panel](./Tircown/Raspberry_plug_panel) | Raspberry mount vertically in the plug panel, allow easy access to ports  | :x: | :x: | :heavy_check_mark: | :x: |
+| | [DIN mount RS-15-5 PSU](./Tircown/DIN_mount_RS-15-5) | A DIN mount for the RS-15-5  | :grey_question: | :grey_question: | :heavy_check_mark: | :grey_question: |
 | togi | [Exhaust housing side fitting](./togi/exhaust_housing_side_fitting) | Moves the exhaust housing bowden fitting 90 degrees to allow the printer to stand closer to a wall | :x: | :x: | :heavy_check_mark: |:x:|
 | warriorofwire | [Slenderfan for Afterburner](./warriorofwire/slenderfan) | Lighter, quieter, smaller Afterburner | :x: | :x: | :heavy_check_mark: |:x:|
 | Weaslus | [Electronics Bay and Enclosure Seperator](./Weaslus/Electronics-Bay-Seperator) | Better enclose chamber and keep heat from electronics | :heavy_check_mark: | :x: | :x: |:x:|

printer_mods/Tircown/DIN_mount_RS-15-5/README.md

@@ -0,0 +1 @@
+DIN support for MeanwWell PSU RS-15-5

printer_mods/Tircown/Display_mount_5inch/README.md

@@ -0,0 +1,26 @@
+# Voron 2.4 5" display tilting support
+**Many thanks to Jo_Thingiverse for having tested this mount.**
+
+### Bill Of Materials
+* Screen 5" 800*480 IPS TFT MIPI DSI Multi-Touch Capacitive Touch Panel LCD Module Display Monitor Screen for Raspberry Pi
+* optional SD extender or microSD extender
+* 2 M3x15
+* 6(+4) M3x8
+* 6 M3 threaded inserts
+* 2 M3 hammered nuts
+
+### Instructions
+1. Put one M3 threaded insert in each arm end.
+2. Put four M3 threaded insert in the back of the screen case.
+3. Remove the built-in support in the fork of both arms.
+4. Install the two slides with M3x8.
+5. Use two pieces of filament as hinges.
+6. Adjust the tension of the screws that pass through the slides to keep the position.
+7. The optional installation of the SD extender requires four self tapping M3x8.
+
+**Since the screen is larger than the original piece you will have to replace your sides skirts. These are included too.**
+
+![CAD](Images/Capture.JPG)
+![photo1](Images/image0.jpg)
+![photo2](Images/image1.jpg)
+![photo3](Images/image3.jpg)

printer_mods/Tircown/Raspberry_plug_panel/readme.md

@@ -0,0 +1,16 @@
+# Voron 2.4 Raspberry vertically installed in plug panel
+
+For the DD11 version I used this reference: SCHURTER DD11.0113.1111
+Many other versions of SHURTER DDXX plugs are compatible. Check out sizes on datasheet.
+
+### Instructions
+1. Put three M3 threaded inserts in the back of the panel.
+2. Install the pi on the bracket with three M2x10 self tapping screws.
+3. Pass the USB cable(s) for inner components such as SKR before attaching the bracket to the panel.
+ There is a notch on the side of the opening for the raspberry to that purpose.
+4. Use three M3x8 to attach the bracket to the raspberry.
+The rest of the installation is pretty similar to the original bracket: check the official manual.
+
+![photo1](Images/image0.jpg)
+![photo2](Images/image1.jpg)
+![photo3](Images/image2.jpg)