Shorter Z Joints, Badge Retractor Mounts, 15x15 Drag Chain Ends by Ellis (#124)

printer_mods/Ellis/15x15_Drag_Chain_End/README.md

@@ -0,0 +1,5 @@
+<B>15x15 Drag Chain End</B>
+
+End pieces for 15x15 drag chains. Designed around Cloudray China chains, but will likely work with other chain brands too.
+
+![Image](Images/Image.png)

printer_mods/Ellis/Badge_Retractor_Mount/README.md

@@ -0,0 +1,12 @@
+<B>Badge Retractor Mount</B>
+
+Just a simple little mod to keep the bowden tube out of the way using a badge retractor. Available in multiple angles.
+
+Designed for this style of badge retractor, but may work with others:
+
+![Example](Images/Example.jpg)
+
+(You probably have one in a drawer somewhere)
+
+<B>25 Degree</B>
+![25 Degree](Images/Image.jpg)

printer_mods/Ellis/Short_Z_Joints/README.md

@@ -0,0 +1,21 @@
+<B>Shorter Z joints for Voron 2.4</B>
+
+This mod reduces the size of the Z joint stack by 12.5mm.
+
+The intent is to increase gantry stability by reducing the leverage on the Z ball joints while throwing the toolhead around.
+
+This is only tested with microswitch XY endstops. There is no hall effect magnet slot, though you may be able to affix one to the upper right screw head.
+
+To use this mod, you will need:
+- 4x M5x30 SHCS/BHCS
+- 4x M5x20 BHCS
+- 4x M3x20 SHCS
+- 4x M5 nylon lock nuts <I>(optional*)</I>
+
+<I>* You can use standard M5 nuts as per the original config, however I prefer nylock nuts here.</I>
+
+<B>Side by Side</B>
+![Side by Side](Images/Side-By-Side.png)
+
+<B>Cross Section</B>
+![Cross Section](Images/Side-By-Side-Cross-Section.png)

printer_mods/README.md

@@ -29,6 +29,9 @@ like so:
 |Badnoob |[Precision AB Drive](./Badnoob/Precision_AB_Drive)|Changes the gearing for the AB drives to improve both resolution and torque, with a strenthened frame. |:grey_question:|:grey_question:|:heavy_check_mark:|
 | |[Rail Alignment](./Badnoob/Rail_Alignment)|Tools and procedure to properly align the rails in 2.4 and Afterburner|:x:|:x:|:heavy_check_mark:|
 |Dan88 |[V0 one-part Skirts](./Dan88/V0skirt) |One part Skirts for the V0 |:heavy_check_mark: |:x: |:x: |
+| Ellis |[15x15 Drag Chain Ends](./Ellis/15x15_Drag_Chain_End) | 15x15 drag chain end pieces | :grey_question: | :grey_question: |:heavy_check_mark: |
+| |[Badge Retractor Mount](./Ellis/Badge_Retractor_Mount) | Extrusion mount for badge retractor to keep bowden tube out of the way. | :grey_question: | :grey_question: |:heavy_check_mark: |
+| |[Short Z Joints](./Ellis/Short_Z_Joints) | Shorter Z joints for the v2.4 |:x: |:x: |:heavy_check_mark: |
 | FreeformFez | [V1.8 Filtered Power Inlet](./FreeformFez/FilteredPower) | V1.6 Filtered Inlet and Rocker Switch for V1.8 | :x: | :heavy_check_mark: | :x: |
 | GSL12 | [Pocketwatch Nema 17](./GSL12/pocketwatch_nema17)| Extruder like Pocketwatch, but with Nema17 instead of Nema14. Maybe for V0 fork with 2020 extrusions, Nema17 and MGN9 or other printers. | :grey_question: | :grey_question: | :grey_question: |
 |hijax_pl_ |[Corner panel clip](./hijax_pl/corner_panel_clip) |V2 panel corner frames using 3-way L brackets in the corners |:x: |:x: |:heavy_check_mark: |