New mods: VSW_Double_60mm_Fan_Mount and AB_Turbo_Mod (#668)

* Added new mod 'VSW_Double_60mm_Fan_Mount'

* Added new mod 'AB_Turbo_Mod'

* AB_Turbo_Mod edits

Added photos

* AB_Turbo_Mod edits

Minor changes to improve print quality

* AB_Turbo_Mod edits

Minor edits to further improve print quality

* Added step file for each mod for GPLv3 compliance

printer_mods/README.md

@@ -19,7 +19,7 @@ Update the following table with the information about your mod:
 
 like so:
 `
-| Creator | [Mod title](link) | Description | :x: | :x: | :x: | :x: | :x:|`
+| Creator | [Mod title](link) | Description | :x: | :x: | :x: | :x: | :x: |`
 
 ---
 
@@ -233,6 +233,8 @@ like so:
 | | [V0 LED Front Bed Mount](./Maverick_/V0_LED_Front_Bed_Mount) | A modification designed to accomodate a Neopixel Jewel (7) in the face of the front bed mount. | :heavy_check_mark: | :x: | :x: |:x:|
 | | [V0 LED Hinge](./Maverick_/V0_LED_Hinge) | A modification designed to accomodate a Neopixel Jewel (7) in the top right hinge of the door. | :heavy_check_mark: | :x: | :x: |:x:|
 | | [V0 TopHat Mini 12864](./Maverick_/V0_TopHat_Mini_12864) | Modified TopHat to mount a Mini 12864. | :heavy_check_mark: | :x: | :x: |:x:|
+| maximilian-foerg | [Afterburner Turbo Mod](./maximilian-foerg/AB_Turbo_Mod) | A purely cosmetic mod for Afterburner | :x: | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: |
+| | [Switchwire Double 60mm Fan Mount](./maximilian-foerg/VSW_Double_60mm_Fan_Mount) | A mount for two (or four) 60mm fans in SW's electronics compartment | :x: | :x: | :x: | :heavy_check_mark: | :x: |
 | MCKURT |[Switchwire Y Belt Tensioner](./Mckurt/Switchwire_Y_Belt_Tensioner) | Switchwie Y axis Belt Tensioner | :x: | :x: | :x: | :heavy_check_mark: | :x: |
 | MCMBen | [Voron0 Block & Tackle Z Belt](./MCMBen/Voron0_Block_and_Tackle_Z_Belt) | A block & tackle belted Z solution using NEMA14. Ratios from 5:1 to 8:1 and friction prevent Z drop when powered off. | :heavy_check_mark: | :x: | :x: | :x: | :x: |
 | Mellow | [V0 Fly-Gemini](./Mellow/V0_Fly-Gemini) | Fly-Gemini adapted model for V0 | :heavy_check_mark: | :x: | :x: | :x: | :x:|

printer_mods/maximilian-foerg/AB_Turbo_Mod/README.md

@@ -0,0 +1,17 @@
+# Voron Afterburner Turbo Mod
+
+This is a **purely cosmetic** mod for the Afterburner to bring it's appearance closer to Stealthburner.
+
+After having seen Stealthburner, Afterburner's design started to look a little dated to me. So I designed this mod.
+It simply replaces both of Afterburner's front parts with a single part. The only new hardware required are two shorter screws.
+
+## BOM
+| Item | Qty. | Note |
+| --- | --- | --- |
+| SHCS M3x20 | 2 | Replace two SHCS M3x30 |
+
+## Images
+![Ab Turbo Image 01](Images/01.png)
+![Ab Turbo Image 02](Images/02.png)
+![Ab Turbo Image 03](Images/03.JPG)
+![Ab Turbo Image 04](Images/04.JPG)

printer_mods/maximilian-foerg/VSW_Double_60mm_Fan_Mount/README.md

@@ -0,0 +1,21 @@
+# Double 60mm Fan Mount for Voron Switchwire
+
+This is a simple mount for two 60mm fans in Switchwire's electronics compartment.
+It uses screws instead of VHB tape and was inspired by [this mod](../../csch0/SW_FanMount_No_Tape).
+Of course you can also print it twice and mount four fans.
+
+Note that using fans in this position only makes sense if you use the deck and bottom panels, as they form an air tunnel.
+Without them, the fans will only blow against the frame and the air will not reach the electronics.
+
+## BOM
+| Item | Qty. | Note |
+| --- | --- | --- |
+| BHCS M5x10 | 2 |
+| M3 Heat Set Insert | 4 |
+| SHCS M3x25 | 4 | Screw length depends on the fans used |
+
+## Images
+![VSW Double 60mm Fan Mount Installed](Images/01.png)
+![VSW Double 60mm Fan Mount Assembly Front](Images/02.png)
+![VSW Double 60mm Fan Mount Assembly Back](Images/03.png)
+![Two VSW Double 60mm Fan Mounts in electronics compartment](Images/04.png)