Add Monster8 v1.0_003 config file (#554)
* Add Monster8 v1.0_003 config file * Address feedback * Add link for thermistors
This commit is contained in:
Stephen Hurd
GitHub
parent
c977a605b8
commit
074f90acb8
|
|
@ -25,12 +25,13 @@ like so:
|
||||||
|
|
||||||
## Klipper
|
## Klipper
|
||||||
|
|
||||||
| Creator | Config title | Description | V0 | V1.8 | V2.4 | VSW |
|
| Creator | Config title | Description | V0 | V1.8 | V2.4 | VSW | VT |
|
||||||
| --- | --- | --- | --- | --- | --- | --- |
|
| --- | --- | --- | --- | --- | --- | --- |
|
||||||
| jaeger | [FYSETC Spider on V1.8](./klipper/jaeger/Spider_1.1_V1.8) | Example configuration and wiring diagram for a FYSETC Spider 1.1 board on the V1.8 | :x: | :heavy_check_mark: | :x: | :x: |
|
| jaeger | [FYSETC Spider on V1.8](./klipper/jaeger/Spider_1.1_V1.8) | Example configuration and wiring diagram for a FYSETC Spider 1.1 board on the V1.8 | :x: | :heavy_check_mark: | :x: | :x: | :x: |
|
||||||
| MarcPot | [Fysetc Spider Board Pins](./klipper/MarcPot/fysetc_spider_pins) | Defines a set of `[board_pins]` aliases for use with the Fysetc Spider controller | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: |
|
| MarcPot | [Fysetc Spider Board Pins](./klipper/MarcPot/fysetc_spider_pins) | Defines a set of `[board_pins]` aliases for use with the Fysetc Spider controller | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: | :x: |
|
||||||
| Mellow | [Fly-Super8 on V2.4](./klipper/Mellow/FLY-Super8) | Example configuration and wiring diagram for a FLY-Super8 board on the V2.4 | :x: | :x: | :heavy_check_mark: | :x: |
|
| Mellow | [Fly-Super8 on V2.4](./klipper/Mellow/FLY-Super8) | Example configuration and wiring diagram for a FLY-Super8 board on the V2.4 | :x: | :x: | :heavy_check_mark: | :x: | :x: |
|
||||||
| revnull | [BTT Octopus Board Pins](./klipper/revnull/btt_octopus_pins) | Defines a set of `[board_pins]` aliases for use with the BTT Octopus controller | :grey_question: | :grey_question: | :heavy_check_mark: | :grey_question: |
|
| revnull | [BTT Octopus Board Pins](./klipper/revnull/btt_octopus_pins) | Defines a set of `[board_pins]` aliases for use with the BTT Octopus controller | :grey_question: | :grey_question: | :heavy_check_mark: | :grey_question: | :x: |
|
||||||
|
| RealDeuce | [MKS Makerbase Monster8 v1.0_003](./klipper/RealDeuce/MKS-Makerbase/Monster8_v1.0_003/) | Configuration and instructions for installing an MKS Makerbase Monster8 board | :x: | :x: | :heavy_check_mark: | :x: | :x: |
|
||||||
---
|
---
|
||||||
|
|
||||||
## RepRapFirmware
|
## RepRapFirmware
|
||||||
|
|
|
||||||
|
|
@ -0,0 +1,53 @@
|
||||||
|
# Voron V2 / Trident - MKS Makerbase Monster8 Wiring
|
||||||
|
|
||||||
|
## Initial Preparation
|
||||||
|
|
||||||
|
Set jumpers as shown:
|
||||||
|
|
||||||
|
|
||||||
|
|
||||||
|
* Green – Add Jumper
|
||||||
|
* Red – Remove Jumper
|
||||||
|
1. Insert only the jumper in the Green and remove all other jumpers in the Red in order to use TMC2209 UART mode.
|
||||||
|
2. Remove all the jumpers of DIAG to avoid the influence of TMC2209 DIAG on the endstop.
|
||||||
|
3. Set the USB-PWR jumper to off to avoid the interaction between the USB 5V of raspberry pi and the DC-DC 5V of the motherboard.
|
||||||
|
4. Set the six jumpers to VIN to set the fan voltage to the system supply voltage.
|
||||||
|
5. Set the jumper to VIN to set the probe voltage to the system supply voltage.
|
||||||
|
6. Set the two jumpers into I2C to enable the I2C output pins.
|
||||||
|
7. Set the jumper to 5V to set the driver power.
|
||||||
|
|
||||||
|
## Wiring
|
||||||
|
|
||||||
|
* Connect 24V and GND (V+ and V-) from the PSU to POWER (marking on rear of board)
|
||||||
|
* Connect the B Motor (gantry left) to Driver0
|
||||||
|
* Connect the A Motor (gantry right) to Driver1
|
||||||
|
* Connect the Z motor (front-left) to Driver2-2 (leaving an empty connector between A and Z)
|
||||||
|
* Connect the Z1 motor to Driver3
|
||||||
|
* Connect the Z2 motor to Driver4
|
||||||
|
* Connect the Z3 motor to Driver5 (v2 only)
|
||||||
|
* Connect the extruder motor to Driver7 (leaving an empty connector between Z3 and E)
|
||||||
|
* Connect the hot end heater to HE0
|
||||||
|
* Connect the bed SSR (DC Control Side) to H-BED (marking on rear of board)
|
||||||
|
* Connect the hot end fan to FAN0
|
||||||
|
* Connect the part cooling fan to FAN1
|
||||||
|
* Connect the chamber exhaust fan to FAN2
|
||||||
|
* Connect the controller fans to HE1
|
||||||
|
* Connect the hot end thermistor to TH0
|
||||||
|
* Connect the bed thermistor to TB
|
||||||
|
* Connect the X endstop to X+
|
||||||
|
* Connect the Y endstop to Y+
|
||||||
|
* Connect the Z endstop to Z-
|
||||||
|
* Connect the probe with BAT85 to Z+
|
||||||
|
* if using a mini12864 display, connect to EXP1 & EXP2, only after completing the steps shown [below](#mini-12864-Display)
|
||||||
|
|
||||||
|
|
||||||
|
|
||||||
|
## mini 12864 Display
|
||||||
|
* See [the mini12864 guide](https://docs.vorondesign.com/build/electrical/mini12864_klipper_guide.html)
|
||||||
|
|
||||||
|
## Other
|
||||||
|
* example config is located [here](Voron2_Monster8_Config.cfg)
|
||||||
|
* full pinout, and other MKS Makerbase documentation is located [here](https://github.com/makerbase-mks/MKS-Monster8/)
|
||||||
|
* Monster8 v1.0_003 pinout is located [here](https://github.com/makerbase-mks/MKS-Monster8/blob/main/hardware/MKS%20Monster8%20V1.0_003/MKS%20Monster8%20V1.0_003%20PIN.pdf)
|
||||||
|
* DIN rail mount for Monster8 is located [here](https://github.com/makerbase-mks/MKS-Monster8/tree/main/STL/MKS%20Monster8%20fixed%20bracket)
|
||||||
|
* Display bracket for MKS mini12864 V3.0 is located [here](https://github.com/makerbase-mks/MKS-Monster8/tree/main/STL/MKS%20Mini12864%20V3.0%20STL)
|
||||||
|
|
@ -0,0 +1,529 @@
|
||||||
|
## Voron Design VORON2.4 250/300/350mm Monster8 TMC2209 UART config
|
||||||
|
|
||||||
|
## *** THINGS TO CHANGE/CHECK: ***
|
||||||
|
## MCU paths [mcu] section
|
||||||
|
## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
|
||||||
|
## Z Endstop Switch location [safe_z_home] section
|
||||||
|
## Homing end position [gcode_macro G32] section
|
||||||
|
## Z Endstop Switch offset for Z0 [stepper_z] section
|
||||||
|
## Probe points [quad_gantry_level] section
|
||||||
|
## Min & Max gantry corner postions [quad_gantry_level] section
|
||||||
|
## PID tune [extruder] and [heater_bed] sections
|
||||||
|
## Fine tune E steps [extruder] section
|
||||||
|
## Lines beginning with #! describe where to connect wires.
|
||||||
|
## Lines beginning with ##----- are placed around sections that need
|
||||||
|
## to be customized for your build size or other hardware
|
||||||
|
|
||||||
|
[mcu]
|
||||||
|
## Obtain definition by "ls -l /dev/serial/by-id/"
|
||||||
|
##--------------------------------------------------------------------
|
||||||
|
serial: /dev/serial/by-id/{YOUR SERIAL}
|
||||||
|
##--------------------------------------------------------------------
|
||||||
|
|
||||||
|
## Uncomment below if you're using the Raspberry uart0 to communicate with Monster8
|
||||||
|
#restart_method: command
|
||||||
|
|
||||||
|
[printer]
|
||||||
|
kinematics: corexy
|
||||||
|
max_velocity: 300
|
||||||
|
max_accel: 3000
|
||||||
|
max_z_velocity: 15 # Max 15 for 12V TMC Drivers, can increase for 24V
|
||||||
|
max_z_accel: 350
|
||||||
|
square_corner_velocity: 5.0
|
||||||
|
|
||||||
|
#####################################################################
|
||||||
|
# X/Y Stepper Settings
|
||||||
|
#####################################################################
|
||||||
|
|
||||||
|
[stepper_x]
|
||||||
|
#! Connected to Driver0:X (B Motor)
|
||||||
|
step_pin: PC14
|
||||||
|
dir_pin: PC13
|
||||||
|
enable_pin: !PC15 # Shared with stepper_y
|
||||||
|
rotation_distance: 40
|
||||||
|
microsteps: 16
|
||||||
|
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
|
||||||
|
#! In X+ Position (X endstop)
|
||||||
|
endstop_pin: PA13 # Pullup on board
|
||||||
|
position_min: 0
|
||||||
|
##--------------------------------------------------------------------
|
||||||
|
|
||||||
|
## Uncomment below for 250mm build
|
||||||
|
#position_endstop: 250
|
||||||
|
#position_max: 250
|
||||||
|
|
||||||
|
## Uncomment for 300mm build
|
||||||
|
#position_endstop: 300
|
||||||
|
#position_max: 300
|
||||||
|
|
||||||
|
## Uncomment for 350mm build
|
||||||
|
#position_endstop: 350
|
||||||
|
#position_max: 350
|
||||||
|
|
||||||
|
##--------------------------------------------------------------------
|
||||||
|
homing_speed: 25 #Max 100
|
||||||
|
homing_retract_dist: 5
|
||||||
|
homing_positive_dir: true
|
||||||
|
|
||||||
|
[tmc2209 stepper_x]
|
||||||
|
uart_pin: PE6
|
||||||
|
interpolate: False
|
||||||
|
run_current: 0.8 # Max 1.4 (tmc2209 limit)
|
||||||
|
sense_resistor: 0.110
|
||||||
|
stealthchop_threshold: 0
|
||||||
|
|
||||||
|
[stepper_y]
|
||||||
|
#! Connected to Driver1:Y (A Motor)
|
||||||
|
step_pin: PE5
|
||||||
|
dir_pin: PE4
|
||||||
|
enable_pin: !PC15 # Shared with stepper_x
|
||||||
|
rotation_distance: 40
|
||||||
|
microsteps: 16
|
||||||
|
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
|
||||||
|
#! In Y+ Position (Y endstop)
|
||||||
|
endstop_pin: PA15 # Pullup on board
|
||||||
|
position_min: 0
|
||||||
|
##--------------------------------------------------------------------
|
||||||
|
|
||||||
|
## Uncomment for 250mm build
|
||||||
|
#position_endstop: 250
|
||||||
|
#position_max: 250
|
||||||
|
|
||||||
|
## Uncomment for 300mm build
|
||||||
|
#position_endstop: 300
|
||||||
|
#position_max: 300
|
||||||
|
|
||||||
|
## Uncomment for 350mm build
|
||||||
|
#position_endstop: 350
|
||||||
|
#position_max: 350
|
||||||
|
|
||||||
|
##--------------------------------------------------------------------
|
||||||
|
homing_speed: 25 #Max 100
|
||||||
|
homing_retract_dist: 5
|
||||||
|
homing_positive_dir: true
|
||||||
|
|
||||||
|
[tmc2209 stepper_y]
|
||||||
|
uart_pin: PE3
|
||||||
|
interpolate: False
|
||||||
|
run_current: 0.8 # Max 1.4 (tmc2209 limit)
|
||||||
|
sense_resistor: 0.110
|
||||||
|
stealthchop_threshold: 0
|
||||||
|
|
||||||
|
#####################################################################
|
||||||
|
# Z Stepper Settings
|
||||||
|
#####################################################################
|
||||||
|
|
||||||
|
#! In Driver2:Z2 Position (Z0 Stepper - Front Left)
|
||||||
|
[stepper_z]
|
||||||
|
step_pin: PE1
|
||||||
|
dir_pin: PE0
|
||||||
|
enable_pin: !PE2
|
||||||
|
rotation_distance: 40
|
||||||
|
gear_ratio: 80:16
|
||||||
|
microsteps: 16
|
||||||
|
#! In Z- Position (Z endstop)
|
||||||
|
endstop_pin: PB13 # Pullup on board
|
||||||
|
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
||||||
|
## (+) value = endstop above Z0, (-) value = endstop below
|
||||||
|
## Increasing position_endstop brings nozzle closer to the bed
|
||||||
|
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
||||||
|
position_endstop: -0.5
|
||||||
|
##--------------------------------------------------------------------
|
||||||
|
|
||||||
|
## Uncomment below for 250mm build
|
||||||
|
#position_max: 240
|
||||||
|
|
||||||
|
## Uncomment below for 300mm build
|
||||||
|
#position_max: 290
|
||||||
|
|
||||||
|
## Uncomment below for 350mm build
|
||||||
|
#position_max: 340
|
||||||
|
|
||||||
|
##--------------------------------------------------------------------
|
||||||
|
position_min: -5
|
||||||
|
homing_speed: 8
|
||||||
|
second_homing_speed: 3
|
||||||
|
homing_retract_dist: 3
|
||||||
|
|
||||||
|
[tmc2209 stepper_z]
|
||||||
|
uart_pin: PB7
|
||||||
|
interpolate: False
|
||||||
|
run_current: 0.8 # Max 1.4 (tmc2209 limit)
|
||||||
|
sense_resistor: 0.110
|
||||||
|
stealthchop_threshold: 0
|
||||||
|
|
||||||
|
#! In Driver3:E0 Position (Z1 Stepper - Rear Left)
|
||||||
|
[stepper_z1]
|
||||||
|
step_pin: PB5
|
||||||
|
dir_pin: PB4
|
||||||
|
enable_pin: !PB6
|
||||||
|
rotation_distance: 40
|
||||||
|
gear_ratio: 80:16
|
||||||
|
microsteps: 16
|
||||||
|
|
||||||
|
[tmc2209 stepper_z1]
|
||||||
|
uart_pin: PB3
|
||||||
|
interpolate: False
|
||||||
|
run_current: 0.8 # Max 1.4 (tmc2209 limit)
|
||||||
|
sense_resistor: 0.110
|
||||||
|
stealthchop_threshold: 0
|
||||||
|
|
||||||
|
#! In Driver4:E1 Position (Z2 Stepper - Rear Right)
|
||||||
|
[stepper_z2]
|
||||||
|
step_pin: PD6
|
||||||
|
dir_pin: PD5
|
||||||
|
enable_pin: !PD7
|
||||||
|
rotation_distance: 40
|
||||||
|
gear_ratio: 80:16
|
||||||
|
microsteps: 16
|
||||||
|
|
||||||
|
[tmc2209 stepper_z2]
|
||||||
|
uart_pin: PD0
|
||||||
|
interpolate: False
|
||||||
|
run_current: 0.8 # Max 1.4 (tmc2209 limit)
|
||||||
|
sense_resistor: 0.110
|
||||||
|
stealthchop_threshold: 0
|
||||||
|
|
||||||
|
## In Driver5:E2 Position (Z3 Stepper - Front Right)
|
||||||
|
[stepper_z3]
|
||||||
|
step_pin: PD2
|
||||||
|
dir_pin: PD1
|
||||||
|
enable_pin: !PD3
|
||||||
|
rotation_distance: 40
|
||||||
|
gear_ratio: 80:16
|
||||||
|
microsteps: 16
|
||||||
|
|
||||||
|
[tmc2209 stepper_z3]
|
||||||
|
uart_pin: PD4
|
||||||
|
interpolate: False
|
||||||
|
run_current: 0.8 # Max 1.4 (tmc2209 limit)
|
||||||
|
sense_resistor: 0.110
|
||||||
|
stealthchop_threshold: 0
|
||||||
|
|
||||||
|
#####################################################################
|
||||||
|
# Extruder
|
||||||
|
#####################################################################
|
||||||
|
|
||||||
|
#! In Driver7:E4 Position (Extruder)
|
||||||
|
[extruder]
|
||||||
|
step_pin: PD13
|
||||||
|
dir_pin: PD12
|
||||||
|
enable_pin: !PD14
|
||||||
|
|
||||||
|
## Update value below when you perform extruder calibration
|
||||||
|
## If you ask for 100mm of filament, but in reality it is 98mm:
|
||||||
|
## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
|
||||||
|
## 22.6789511 is a good starting point for Bondtech 5mm gears
|
||||||
|
## 34.37086 for Bondtech 8mm gears (Galileo)
|
||||||
|
rotation_distance: 22.6789511 #Bondtech 5mm Drive Gears
|
||||||
|
## Update Gear Ratio depending on your Extruder Type
|
||||||
|
## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
|
||||||
|
## Use 80:20 for M4, M3.1
|
||||||
|
## Use 7.5:1 for Galileo
|
||||||
|
gear_ratio: 50:17 #BMG Gear Ratio
|
||||||
|
microsteps: 16
|
||||||
|
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
|
||||||
|
nozzle_diameter: 0.400
|
||||||
|
filament_diameter: 1.75
|
||||||
|
#! In HE0 Position (Hotend heater)
|
||||||
|
heater_pin: PB1
|
||||||
|
## Validate the following thermistor type to make sure it is correct
|
||||||
|
## See https://www.klipper3d.org/Config_Reference.html#common-thermistors for additional options
|
||||||
|
#sensor_type: ATC Semitec 104GT-2
|
||||||
|
#! In TH0 Position (Hotend thermistor)
|
||||||
|
sensor_pin: PC1
|
||||||
|
min_temp: 10
|
||||||
|
max_temp: 270
|
||||||
|
max_power: 1.0
|
||||||
|
min_extrude_temp: 170
|
||||||
|
control = pid
|
||||||
|
pid_kp = 26.213
|
||||||
|
pid_ki = 1.304
|
||||||
|
pid_kd = 131.721
|
||||||
|
## Try to keep pressure_advance below 1.0
|
||||||
|
#pressure_advance: 0.05
|
||||||
|
## Default is 0.040, leave stock
|
||||||
|
#pressure_advance_smooth_time: 0.040
|
||||||
|
|
||||||
|
[tmc2209 extruder]
|
||||||
|
uart_pin: PD11
|
||||||
|
interpolate: False
|
||||||
|
run_current: 0.5
|
||||||
|
sense_resistor: 0.110
|
||||||
|
stealthchop_threshold: 0
|
||||||
|
|
||||||
|
#####################################################################
|
||||||
|
# Bed Heater
|
||||||
|
#####################################################################
|
||||||
|
[heater_bed]
|
||||||
|
#! In H-BED position (SSR)
|
||||||
|
heater_pin: PB10
|
||||||
|
## Validate the following thermistor type to make sure it is correct
|
||||||
|
## See https://www.klipper3d.org/Config_Reference.html#common-thermistors for additional options
|
||||||
|
#sensor_type: Generic 3950
|
||||||
|
#! In TB position (Bed Thermistor)
|
||||||
|
sensor_pin: PC0 # Pullup on board
|
||||||
|
## Adjust Max Power so your heater doesn't warp your bed
|
||||||
|
## Guidance is 0.4W/cm², so 250W for 250x250, 360W for 300x300,
|
||||||
|
## and 490W for 350x350.
|
||||||
|
## Adjust max_power so the wattage of your heater times the set value
|
||||||
|
## equals the suggested number of watts.
|
||||||
|
## For example, the suggested Keenovo for a 350x350 is a 750W heater.
|
||||||
|
## 490 ÷ 750 = 0.653... so 0.65 is a good value
|
||||||
|
max_power: 0.6
|
||||||
|
min_temp: 0
|
||||||
|
max_temp: 120
|
||||||
|
control: pid
|
||||||
|
pid_kp: 58.437
|
||||||
|
pid_ki: 2.347
|
||||||
|
pid_kd: 363.769
|
||||||
|
|
||||||
|
#####################################################################
|
||||||
|
# Probe
|
||||||
|
#####################################################################
|
||||||
|
|
||||||
|
[probe]
|
||||||
|
## This probe is not used for Z height, only Quad Gantry Leveling
|
||||||
|
#! In Z+ position (Probe)
|
||||||
|
## If your probe is NO instead of NC, change pin to !PB12
|
||||||
|
pin: PB12 # TODO: Pullup on board through JP4 whatever that is...
|
||||||
|
x_offset: 0
|
||||||
|
y_offset: 25.0
|
||||||
|
z_offset: 0
|
||||||
|
speed: 10.0
|
||||||
|
samples: 3
|
||||||
|
samples_result: median
|
||||||
|
sample_retract_dist: 3.0
|
||||||
|
samples_tolerance: 0.006
|
||||||
|
samples_tolerance_retries: 3
|
||||||
|
|
||||||
|
#####################################################################
|
||||||
|
# Fan Control
|
||||||
|
#####################################################################
|
||||||
|
|
||||||
|
[heater_fan hotend_fan]
|
||||||
|
#! FAN0 Connector (Hotend Fan)
|
||||||
|
pin: PA2
|
||||||
|
max_power: 1.0
|
||||||
|
#kick_start_time: 0.5
|
||||||
|
heater: extruder
|
||||||
|
heater_temp: 50.0
|
||||||
|
## If you are experiencing back flow, you can reduce fan_speed
|
||||||
|
#fan_speed: 1.0
|
||||||
|
|
||||||
|
[fan]
|
||||||
|
#! FAN1 Connector (Print Cooling Fan)
|
||||||
|
pin: PA1
|
||||||
|
#max_power: 1.0
|
||||||
|
#kick_start_time: 0.5
|
||||||
|
## Depending on your fan, you may need to increase this value
|
||||||
|
## if your fan will not start. Can change cycle_time (increase)
|
||||||
|
## if your fan is not able to slow down effectively
|
||||||
|
off_below: 0.10
|
||||||
|
|
||||||
|
[controller_fan controller_fan]
|
||||||
|
#! In HE1 Positon (Controller fan)
|
||||||
|
pin: PB0
|
||||||
|
kick_start_time: 0.5
|
||||||
|
heater: heater_bed
|
||||||
|
heater_temp: 45.0
|
||||||
|
|
||||||
|
# Uncomment this for a GCode controllable fan
|
||||||
|
#[heater_fan exhaust_fan]
|
||||||
|
#! FAN2 Connector (Exhaust fan)
|
||||||
|
#pin: PA0
|
||||||
|
#max_power: 1.0
|
||||||
|
#shutdown_speed: 0.0
|
||||||
|
##kick_start_time: 0.5
|
||||||
|
#heater: heater_bed
|
||||||
|
#heater_temp: 60
|
||||||
|
#fan_speed: 1.0
|
||||||
|
|
||||||
|
# Uncomment this for an automatic chamber temperature fan
|
||||||
|
#[temperature_fan chamber]
|
||||||
|
##! FAN2 Connector (Exhaust fan)
|
||||||
|
#pin: PA0
|
||||||
|
#max_power: 1.0
|
||||||
|
#shutdown_speed: 0.0
|
||||||
|
## Validate the following thermistor type to make sure it is correct
|
||||||
|
## See https://www.klipper3d.org/Config_Reference.html#common-thermistors for additional options
|
||||||
|
#sensor_type: Generic 3950
|
||||||
|
##! In TH1 Position (Chamber Temperature)
|
||||||
|
#sensor_pin: PC2
|
||||||
|
#control: watermark
|
||||||
|
#min_temp: 0
|
||||||
|
#max_temp: 70
|
||||||
|
#target_temp: 35.0
|
||||||
|
#gcode_id: C
|
||||||
|
|
||||||
|
#####################################################################
|
||||||
|
# LED Control
|
||||||
|
#####################################################################
|
||||||
|
|
||||||
|
#[output_pin caselight ]
|
||||||
|
#! In HE2 Position (Chamber Lighting)
|
||||||
|
#pin: PA3
|
||||||
|
#pwm: true
|
||||||
|
#shutdown_value: 0
|
||||||
|
#cycle_time: 0.01
|
||||||
|
|
||||||
|
#####################################################################
|
||||||
|
# Homing and Gantry Adjustment Routines
|
||||||
|
#####################################################################
|
||||||
|
|
||||||
|
[idle_timeout]
|
||||||
|
timeout: 1800
|
||||||
|
|
||||||
|
[safe_z_home]
|
||||||
|
## XY Location of the Z Endstop Switch
|
||||||
|
## Update -10,-10 to the XY coordinates of your endstop pin
|
||||||
|
## (such as 157,305) after going through Z Endstop Pin
|
||||||
|
## Location Definition step.
|
||||||
|
home_xy_position:-10,-10
|
||||||
|
speed:100
|
||||||
|
z_hop:10
|
||||||
|
|
||||||
|
[quad_gantry_level]
|
||||||
|
## Use QUAD_GANTRY_LEVEL to level a gantry.
|
||||||
|
## Min & Max gantry corners - measure from nozzle at MIN (0,0) and
|
||||||
|
## MAX (250, 250), (300,300), or (350,350) depending on your printer size
|
||||||
|
## to respective belt positions
|
||||||
|
|
||||||
|
#--------------------------------------------------------------------
|
||||||
|
## Gantry Corners for 250mm Build
|
||||||
|
## Uncomment for 250mm build
|
||||||
|
#gantry_corners:
|
||||||
|
# -60,-10
|
||||||
|
# 310, 320
|
||||||
|
## Probe points
|
||||||
|
#points:
|
||||||
|
# 50,25
|
||||||
|
# 50,175
|
||||||
|
# 200,175
|
||||||
|
# 200,25
|
||||||
|
|
||||||
|
## Gantry Corners for 300mm Build
|
||||||
|
## Uncomment for 300mm build
|
||||||
|
#gantry_corners:
|
||||||
|
# -60,-10
|
||||||
|
# 360,370
|
||||||
|
## Probe points
|
||||||
|
#points:
|
||||||
|
# 50,25
|
||||||
|
# 50,225
|
||||||
|
# 250,225
|
||||||
|
# 250,25
|
||||||
|
|
||||||
|
## Gantry Corners for 350mm Build
|
||||||
|
## Uncomment for 350mm build
|
||||||
|
#gantry_corners:
|
||||||
|
# -60,-10
|
||||||
|
# 410,420
|
||||||
|
## Probe points
|
||||||
|
#points:
|
||||||
|
# 50,25
|
||||||
|
# 50,275
|
||||||
|
# 300,275
|
||||||
|
# 300,25
|
||||||
|
|
||||||
|
#--------------------------------------------------------------------
|
||||||
|
speed: 100
|
||||||
|
horizontal_move_z: 10
|
||||||
|
retries: 5
|
||||||
|
retry_tolerance: 0.0075
|
||||||
|
max_adjust: 10
|
||||||
|
|
||||||
|
#####################################################################
|
||||||
|
# Displays
|
||||||
|
#####################################################################
|
||||||
|
|
||||||
|
#--------------------------------------------------------------------
|
||||||
|
|
||||||
|
[display]
|
||||||
|
#! In EXP1/EXP2 (mini12864 LCD Display)
|
||||||
|
lcd_type: uc1701
|
||||||
|
cs_pin: PE11
|
||||||
|
a0_pin: PD10
|
||||||
|
rst_pin: PD9
|
||||||
|
encoder_pins: ^PE8,^PE9
|
||||||
|
click_pin: ^!PE10
|
||||||
|
contrast: 63
|
||||||
|
#spi_bus: spi1
|
||||||
|
spi_software_mosi_pin: PA7
|
||||||
|
spi_software_miso_pin: PA6
|
||||||
|
spi_software_sclk_pin: PA5
|
||||||
|
|
||||||
|
[neopixel mks_mini12864_v3]
|
||||||
|
# To control Neopixel RGB in mini12864 display
|
||||||
|
pin: PD8
|
||||||
|
chain_count: 3
|
||||||
|
initial_RED: 0.1
|
||||||
|
initial_GREEN: 0.5
|
||||||
|
initial_BLUE: 0.0
|
||||||
|
color_order: RGB
|
||||||
|
|
||||||
|
# Set RGB values on boot up for each Neopixel.
|
||||||
|
# Index 1 = display, Index 2 and 3 = Knob
|
||||||
|
[delayed_gcode setdisplayneopixel]
|
||||||
|
initial_duration: 1
|
||||||
|
gcode:
|
||||||
|
SET_LED LED=mks_mini12864_v3 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0
|
||||||
|
SET_LED LED=mks_mini12864_v3 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0
|
||||||
|
SET_LED LED=mks_mini12864_v3 RED=1 GREEN=0 BLUE=0 INDEX=3
|
||||||
|
|
||||||
|
[output_pin beeper]
|
||||||
|
pin: PB2
|
||||||
|
|
||||||
|
#--------------------------------------------------------------------
|
||||||
|
|
||||||
|
|
||||||
|
#####################################################################
|
||||||
|
# Macros
|
||||||
|
#####################################################################
|
||||||
|
|
||||||
|
[gcode_macro G32]
|
||||||
|
gcode:
|
||||||
|
BED_MESH_CLEAR
|
||||||
|
G28
|
||||||
|
QUAD_GANTRY_LEVEL
|
||||||
|
G28
|
||||||
|
## Uncomment for for your size printer:
|
||||||
|
#--------------------------------------------------------------------
|
||||||
|
## Uncomment for 250mm build
|
||||||
|
#G0 X125 Y125 Z30 F3600
|
||||||
|
|
||||||
|
## Uncomment for 300 build
|
||||||
|
#G0 X150 Y150 Z30 F3600
|
||||||
|
|
||||||
|
## Uncomment for 350mm build
|
||||||
|
#G0 X175 Y175 Z30 F3600
|
||||||
|
#--------------------------------------------------------------------
|
||||||
|
|
||||||
|
[gcode_macro M300]
|
||||||
|
gcode:
|
||||||
|
# Use a 200ms duration if P is omitted.
|
||||||
|
{% set P = params.P|default(200)|int %}
|
||||||
|
SET_PIN PIN=BEEPER_pin VALUE=1
|
||||||
|
G4 P{P}
|
||||||
|
SET_PIN PIN=BEEPER_pin VALUE=0
|
||||||
|
|
||||||
|
[gcode_macro PRINT_START]
|
||||||
|
# Use PRINT_START for the slicer starting script - please customise for your slicer of choice
|
||||||
|
gcode:
|
||||||
|
G32 ; home all axes
|
||||||
|
G1 Z20 F3000 ; move nozzle away from bed
|
||||||
|
|
||||||
|
[gcode_macro PRINT_END]
|
||||||
|
# Use PRINT_END for the slicer ending script - please customise for your slicer of choice
|
||||||
|
gcode:
|
||||||
|
M400 ; wait for buffer to clear
|
||||||
|
G92 E0 ; zero the extruder
|
||||||
|
G1 E-10.0 F3600 ; retract filament
|
||||||
|
G91 ; relative positioning
|
||||||
|
G0 Z1.00 X20.0 Y20.0 F20000 ; move nozzle to remove stringing
|
||||||
|
TURN_OFF_HEATERS
|
||||||
|
M107 ; turn off fan
|
||||||
|
G1 Z2 F3000 ; move nozzle up 2mm
|
||||||
|
G90 ; absolute positioning
|
||||||
|
G0 X125 Y250 F3600 ; park nozzle at rear
|
||||||
|
BED_MESH_CLEAR
|
||||||
Binary file not shown.
|
After Width: | Height: | Size: 345 KiB |
Binary file not shown.
|
After Width: | Height: | Size: 369 KiB |
Loading…
Reference in New Issue