131 lines
6.0 KiB
Plaintext
131 lines
6.0 KiB
Plaintext
; Configuration file for Duet 3 (firmware version 3)
|
|
; executed by the firmware on start-up
|
|
;
|
|
; generated by RepRapFirmware Configuration Tool v3.1.3 on Sun Jul 12 2020 20:53:52 GMT+0200 (Central European Summer Time)
|
|
|
|
; General preferences
|
|
G90 ; send absolute coordinates...
|
|
M83 ; ...but relative extruder moves
|
|
M550 P"Voron" ; set printer name
|
|
M669 K1 ; select CoreXY mode
|
|
|
|
; Network
|
|
M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP
|
|
M586 P0 S1 ; enable HTTP
|
|
M586 P1 S0 ; disable FTP
|
|
M586 P2 T1 S0 ; disable Telnet
|
|
|
|
; Wait a bit so boards can sync up
|
|
G4 S5
|
|
|
|
; Drives for XY
|
|
M569 P0.4 S1 ; A motor
|
|
M569 P0.5 S1 ; B motor
|
|
|
|
; Drives for Z
|
|
M569 P0.0 S0 ; Front left
|
|
M569 P0.1 S1 ; Back left
|
|
M569 P0.2 S0 ; Back right
|
|
M569 P0.3 S1 ; Front right
|
|
|
|
; Drive for extruder
|
|
M569 P2.0 S0 ; physical drive 1.0 goes forwards
|
|
|
|
; Drive mappings
|
|
M584 X0.4 Y0.5 Z0.0:0.1:0.2:0.3 E2.0 ; set drive mapping
|
|
|
|
; General drive config like speeds, accel, jerk, etc
|
|
M350 X16 Y16 Z16:16:16:16 E16 I1 ; configure microstepping with interpolation
|
|
M92 X80.00 Y80.00 Z400.00 E410.00 ; set steps per mm
|
|
M566 X600.00 Y600.00 Z60.00 E8000.00 ; set maximum instantaneous speed changes (mm/min)
|
|
M203 X18000.00 Y18000.00 Z3000 E15000 ; set maximum speeds (mm/min)
|
|
M201 X1500.00 Y1500.00 Z350.00 E1800.00 ; set accelerations (mm/s^2)
|
|
M204 P1500 T2000 ; set printing acceleration and travel acceleration
|
|
M906 X1200 Y1200 Z1200 E600 I60 ; set motor currents (mA) and motor idle factor in per cent
|
|
M84 S30
|
|
|
|
; Axis Limits
|
|
M208 X1 Y0 Z0 S1 ; set axis minima
|
|
M208 X301 Y305 Z265 S0 ; set axis maxima
|
|
|
|
; Endstops
|
|
M574 X2 S1 P"!io1.in" ; X Hall effect endstop
|
|
M574 Y2 S1 P"!io2.in" ; Y Hall effect endstop
|
|
M574 Z0 P"nil" ; No endstop
|
|
|
|
; Z microswitch
|
|
M558 K1 P8 C"io3.in" I1 H2 F350:60 T18000 A10 S0.01 R0.2 ; set Z probe type to switch and the dive height + speeds
|
|
G31 K1 P500 X0 Y0 Z-0.17 ; set Z probe trigger value, offset and trigger height -0.8
|
|
|
|
; Z-Probe
|
|
M558 K0 P8 C"io4.in" I1 H5 F350:120 T18000 A5 S0.01 R0.2 ; set Z probe type to switch and the dive height + speeds
|
|
G31 K0 P500 X0 Y25 Z1.98 ; set Z probe trigger value, offset and trigger height
|
|
|
|
M671 X354:354:-53:-53 Y0:370:370:0 S20 ; Define Z belts locations (Front_Left, Back_Left, Back_Right, Front_Right)
|
|
M557 X15:285 Y25:275 S40 ; define mesh grid
|
|
|
|
; Hotbed
|
|
M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; Thermistor
|
|
M950 H0 C"out0" T0 ; Heater
|
|
M307 H0 R0.799 C380.0 D4.51 S0.60 V24.0 ; Heater 0 model for 3.x
|
|
M140 H0 ; Map heated bed to heater 0
|
|
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
|
|
M570 H0 T3 ; Start screaming if temp falls 3C below set temp.
|
|
|
|
; Hotend
|
|
M308 S1 P"temp1" Y"pt1000" ; PT1000 on main board
|
|
M950 H1 C"out1" T1 ; Heater
|
|
|
|
; Mosquitto
|
|
M307 H1 R2.921 C156.5 D5.20 S1.00 V24.0
|
|
|
|
; DHT22 sensor
|
|
M308 S10 P"0.spi.cs1" Y"dht22" A"Chamber Temp" ; Temperature (connected to cs0 port on the temp daughterboard slot
|
|
M308 S11 P"S10.1" Y"dhthumidity" A"Chamber Hum[%]" ; Humidity
|
|
|
|
; Main fans
|
|
M950 F0 C"2.out6" Q500 ; Part cooling fan
|
|
M106 P0 S0 H-1 C"Part Fan" ; Default off; thermostatic control off
|
|
M950 F1 C"out7" Q500 ; Hotend cooling fan
|
|
M106 P1 S1 H1 T45 C"Hotend Fan" ; Default on; thermistatic control on above 45C
|
|
|
|
; Aux fans (option to control daughter board fans based on main board temp sensor coming in RRF3.3, for now has to be manual)
|
|
M950 F2 C"out8" Q500 ; Electronics compartment fan 1
|
|
M106 P2 S1 H0 T45 C"Electronics Fan 1" ; Default off; thermistatic control on above 45C
|
|
M950 F3 C"out9" Q500 ; Electronics compartment fan 2
|
|
M106 P3 S1 H0 T45 C"Electronics Fan 2" ; Default off; thermistatic control on above 45C
|
|
|
|
M950 F4 C"!out4+out4.tach" ; Noctua exhaust filter fan
|
|
M106 P4 S0 H-1 C"Exhaust Fan" ; Default off
|
|
|
|
M950 F7 C"out5+out5.tach" Q500 ; Electronics compartment fan 1
|
|
M106 P7 S0 H-1 C"Nevermore" ; Default off; thermistatic control on above 45C
|
|
|
|
; Tools
|
|
M563 P0 D0 H1 F0 ; define tool 0
|
|
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
|
|
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
|
|
|
|
; Push buttons and their config
|
|
M950 J5 C"io5.in" ; Left button - light
|
|
M581 P5 T5 ; when button pushed, execute trigger5.g
|
|
|
|
M950 J6 C"io7.in" ; Left button - heat up
|
|
M950 F5 C"io6.out" ; configure the relay as fan
|
|
M106 F5 S0 H-1 C"Light"
|
|
M581 P6 T6 ; When pushed - trigger relay switch on io6.out
|
|
|
|
; Custom settings are not defined
|
|
M593 F37.3 ; DAA
|
|
|
|
; Calibration of the MCU temp sensor
|
|
M912 P0 S-9.2
|
|
|
|
; Miscellaneous
|
|
M911 S22 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
|
|
M575 P1 S1 B57600 ; enable support for PanelDue
|
|
|
|
; Prepare global vars for print macros
|
|
global bed_temp = 0
|
|
global hotend_temp = 0
|