Parametric Spool Holder (#422)

* Parametric Spool Holder

* Fix review comments

printer_mods/README.md

@@ -124,6 +124,7 @@ like so:
 | | [Voron2.4_Pins_Mod](./hartk1213/Voron2.4_Pins_Mod) | This mod replaces all the M5 screws for all idlers/pulleys/bearings with 5mm pins  | :x:| :x: | :heavy_check_mark: |:x:|
 | | [Voron2.4_Y_Endstop_Relocation](./hartk1213/Voron2.4_Y_Endstop_Relocation) | This mod relocates the Y endstop to the top A drive piece, to work with Arkeets MGN12 mod  | :x:| :x: | :heavy_check_mark: |:x:|
 | henrikssn | [Plug Panel Mod for Generic Unfiltered Modules](./henrikssn/plug_panel_generic) | v2.4 plug panel for generic unfiltered modules with 66mm x 27mm cutout such as the Delta 06A2 and Qualtek 761-18 | :x: | :x: | :heavy_check_mark: | :x:|
+| | [Parametric Spool Holder](./henrikssn/parametric_spool_holder) | Spool holder where the length is a parameter. | :x: | :heavy_check_mark: | :heavy_check_mark: |:x:  | :heavy_check_mark:|
 | hernsl | [Bottom Panel Mag Clip](./hernsl/bottom_panel_mag_clip) | v2.4 magnetic clips to retain bottom panel | :x: | :x: | :heavy_check_mark: |:x:|
 |hijax_pl_ |[Corner panel clip](./hijax_pl/corner_panel_clip) |V2 panel corner frames using 3-way L brackets in the corners |:x: |:x: |:heavy_check_mark: |:x:|
 | |[Din Rail mount](./hijax_pl/din_rail_mount) |Adapter to attach DIN Rail to 2020 extrusion. |:x: |:x: |:heavy_check_mark: |:x:|
@@ -168,7 +169,7 @@ like so:
 | | [Mosquito PTFE 15mm Tube Cutting Jig](./LoCoCNC/Mosquito_PTFE_Cutting_Jig) | Tool to precicely cut 15mm PTFE Tube |:heavy_check_mark:|:x:|:x:|:x:|
 | | [3mm Top Hat Panels Clips](./LoCoCNC/3mm_tophat_panel_parts) | Required to use the 3mm (1/8") thick top hat panels for V0.1 |:heavy_check_mark:|:x:|:x:|:x:|
 | | [Strain Relief w/ 10 Pin Microfit](./LoCoCNC/Strain_Relief_w_Microfit) | Strain Relief with 10 pin Microfit connector |:heavy_check_mark:|:x:|:x:|:x:|
-| | [SSR Mounting Strap](./LoCoCNC/ssr_strap) | Mounting Strap for SSR on 1515 Extrusions |:heavy_check_mark:|:x:|:x:|:x:| 
+| | [SSR Mounting Strap](./LoCoCNC/ssr_strap) | Mounting Strap for SSR on 1515 Extrusions |:heavy_check_mark:|:x:|:x:|:x:|
 | | [V2.4 Bed Wiring Grommet](./LoCoCNC/wire_grommets) | Safely capture your bed wires thru the bottom panel |:x:|:x:|:heavy_check_mark:|:x:|
 |Long| [Mantis Dual 5015 Toolhead](./Long/Mantis_Dual_5015) | MGN12 Dual 5015 Toolhead for 2.4 & 1.8 |:x:|:heavy_check_mark:|:heavy_check_mark:|:x:|
 |Majarspeed| [Hartk board mount galileo](./Majarspeed/Hartk_Mount_Galileo) | It hangs stuff on your tool | :x: | :x: | :heavy_check_mark: | :x: |
@@ -204,7 +205,7 @@ like so:
 |padok |[Chain Anchor - ADXL345 mount Mod](./padok/chain_anchor-ADXL345_mount) | A ADXL345 mount for the Afterburner |:x: |:grey_question: |:heavy_check_mark: |:grey_question: |
 |Phalanx |["Other" Idlers Mod](./Phalanx/Other-V2-Idlers/) | Allow usage of wider toolheads on the V2 |:x: |:grey_question: |:heavy_check_mark: |:x:|
 |piet206 |[V1.8 Z Rails Mod](./piet206/V1.8._Z_Rails_Mod) | Add MGN12H linear rails for Z axis motion |:x: |:heavy_check_mark: |:x: |:x:|
-| Printopal | [Magnetic top panel](Printopal/Magnetic_top_panel) | Top panel with magnets allows for quick installation and removal | :x: | :heavy_check_mark:| :heavy_check_mark: | :x: | 
+| Printopal | [Magnetic top panel](Printopal/Magnetic_top_panel) | Top panel with magnets allows for quick installation and removal | :x: | :heavy_check_mark:| :heavy_check_mark: | :x: |
 |QuackProfit|[V0 Adafruit NeoPixel LED Mounts](./QuackProfit/V0-Adafruit-Y_Rails) | Mount Adafruit PCB NeoPixel Sticks on the V0 Y-rail extrusions | :heavy_check_mark:|:x:|:x:|:x:|
 |randell   |[Door Hinges](./randell/Door_Hinges) |Door hinges that use an M3 bolt for a pin and bolts thru the panel |:x: |:x: |:heavy_check_mark: |:x:|
 ||[Microswitch Pod for PCB](./randell/Microswitch_Endstop) |Modified endstop pod for use of endstop switches mounted on a PCB |:x: |:x: |:heavy_check_mark: |:x:|

printer_mods/henrikssn/parametric_spool_holder/README.md

@@ -0,0 +1,5 @@
+# Parametric Spool Holder
+
+### OVERVIEW:
+
+Spool holder where the length is a parameter, anything from 25mm up to ~150mm is supported.