Addition of my Mod PiTFT Mount (#720)

* Added PiTFT Mount

Added PiTFT Mount

* Update readme.md

* Create STL

* Add files via upload

* Delete STL

* Create readme.md

* Added STL files

* Delete [a]_display_mount_x2.stl

* Delete display_middle_skirt.stl

* Delete pitft70_housing_front.stl

* Delete pitft70_housing_rear.stl

* Create placeholder.md

* Added Some Pictures

* Update readme.md

* Add files via upload

* Update readme.md

* Update readme.md

* Delete printer_mods/Mac10goesBRRRT/BTT_PiTFT/Pictures directory

* Add files via upload

* Update readme.md

* Update readme.md

* Update readme.md

* Update readme.md

* Update readme.md

* Update readme.md

* Update readme.md

* Update readme.md

* Delete Display_Far.jpg

* Delete Display_Close.jpg

* Add files via upload

* Update readme.md

* Added Pictures and updated Instructions

* Update readme.md

* Added Printing Instructions

* Add files via upload

* Update readme.md

* Update readme.md

* Added my Entry in the List

* Delete printer_mods/Mac10goesBRRRT/BTT_PiTFT/SLT directory

* Add files via upload

printer_mods/Mac10goesBRRRT/BTT_PiTFT/readme.md

@@ -0,0 +1,44 @@
+# Overview:
+
+This mod adds a mount for the BigTreeTech PiTFT. Currently the mod works for the PiTFT70, but im planning on adding a 5" and 3,5" option.
+The Mount allows the doors to work without any mods and doesnt protude beyond the Skirts. It adds about 11cm to the depth of the printer.
+
+![Render](images/PiTFT_Render.png)
+
+
+
+## BOM:
+
+- 1x M3 T-Nut/Hammerhead Nut
+- 1x M3x8mm SHCS
+- 2x M5 T-Nut/Hammerhead Nut
+- 2x M5x10mm BHCS
+- 4x M2,5x14mm BHCS _**OR**_ 4x any M2,5 longer than 6mm
+- 1x PiTFT70
+- 1x Flat Flexible Cable 50cm or longer for Pi Cam/Pi Display
+
+M2,5x14mm screws are included in the Display, the included Flex Cable is too short.
+
+![Picture with some Distance](images/Display_Front.jpg)
+
+## Printing
+
+All Parts are already in the right orientation. Use the standard Voron Specs for printing.
+
+## Installation
+
+1. Attach the 2 Mounts to the Frame with the M5 screws, feed the Cable through the Slot in the middle Skirt and mount it with the M3 screws.
+
+2. Feed the Cable through the back of the Housing and attach it to the Display (unisolated part faces display). Use the Raspberry Mounts to attach the Display/Housing to the Frame.
+
+3. Simply Push the Front Housing onto the back, it should fit
+
+4. Connect the FFC to the Pis Display port (unisolated part faces towards USB).
+
+5. Install Klipperscreen via KIAUTH or by doing it manually.
+
+6. If the Display is flipped upside down, hit the toggle switch. Adjust the brightness as needed.
+
+Here is a picture of how the FFC should be routed:
+
+![How to Route the FFC](images/FFC-Routing.jpg)

printer_mods/README.md

@@ -242,6 +242,7 @@ like so:
 ||[Trident Inverted Electronics](./LoganFraser/TridentInvertedElectronics) | Flip the Trident electronics bay for top access.  |:x:|:x:|:x:|:x:|:heavy_check_mark:|
 ||[WagoMounts](./LoganFraser/WagoMounts) | Wago Mounts for Din Rail or 2020 Extrusion mounting. |:grey_question:|:grey_question:|:heavy_check_mark:|:heavy_check_mark:|:heavy_check_mark:|
 |Long| [Mantis Dual 5015 Toolhead](./Long/Mantis_Dual_5015) | MGN12 Dual 5015 Toolhead for 2.4 & 1.8 |:x:|:heavy_check_mark:|:heavy_check_mark:|:x:|
+|Mac10goesBRRRT| [PiTFT Mount](./Mac10goesBRRRT/BTT_PiTFT) | Mount for the BTT PiTFT Touchscreen |:x:|:grey_question:|:heavy_check_mark:|:grey_question:|:heavy_check_mark:|
 |Majarspeed| [Hartk board mount galileo](./Majarspeed/Hartk_Mount_Galileo) | It hangs stuff on your tool | :x: | :x: | :heavy_check_mark: | :x: |
 |MakeALeft| [Switchwire Clean Center Grill](./MakeALeft/Switchwire_Front_Grill) | Removed magnet holders on center panel for cleaner look | :x: | :x: | :x: | ✔️ | :x:
 |madfabrications |[Vertical PSU Mount](./madfabrications/Vertical_PSU_Mount) |Mounts the PSU vertically on the DIN rails|:x: |:x: |:heavy_check_mark:|:x:|