Add DIN mount for Fysetc S6 V2 (#296)

* Add DIN mount for Fysetc S6 V2

* Misc fixes for Fysetc S6 V2 mount

* Fix Fysetc S6 V2 STL orientation

printer_mods/README.md

@@ -41,8 +41,6 @@ like so:
 | |[Magnetic hotend fan cover](./arkeet/magnet-fan-cover)|A replacement hotend fan cover, held with magnets instead of screws. |:x:|:heavy_check_mark:|:heavy_check_mark:|:heavy_check_mark:|
 | |[MGN12 X-axis](./arkeet/mgn12/)|Replaces the dual MGN9H rails with a single MGN12H. |:x:|:x:|:heavy_check_mark:|:x:|
 | |[V0 DC inlet](./arkeet/v0-dc-inlet/)|Skirt inlet for external 24V DC power supply. |:heavy_check_mark:|:x:|:x:|:x:|
-|claytono|[Voron 2.4 Extrusion Jig](./claytono/2.4-extrusion-jig)|A jig help align extrusions to get a properly square frame |:x:|:x:|:heavy_check_mark:|:x:|
-||[V0 Zip Tie Skirts](./claytono/v0-zip-tie-skirts)|V0 skirts with small loops added along the top to allow zip tyiing cables to them|:heavy_check_mark:|:x:|:x:|:x:
 |Badnoob |[Precision AB Drive](./Badnoob/Precision_AB_Drive)|Changes the gearing for the AB drives to improve both resolution and torque, with a strenthened frame. |:grey_question:|:grey_question:|:heavy_check_mark:|:x:|
 | |[Rail Alignment](./Badnoob/Rail_Alignment)|Tools and procedure to properly align the rails in 2.4 and Afterburner|:x:|:x:|:heavy_check_mark:|:x:|
 | BladeScraper-Designs | [Microswitch_Pod_With_Connector](./BladeScraper-Designs/Microswitch_Pod_With_Conector) | Microswitch pod with JST-XH 4-pin connector | :x: |:x: |:heavy_check_mark: | :x:
@@ -53,6 +51,9 @@ like so:
 | buzzdalf | [v1.8/2.4 Afterburner connector cover for 42STH20-1004AS](./buzzdalf/connector_cover) | v1.8/2.4 Connector cover for 42STH20-1004AS | :x: | :heavy_check_mark: | :heavy_check_mark: |:grey_question:|
 ||[Ender 3 Switchwire Taller Z Mod](./buzzdalf/ender_switchwire_taller_z) | Taller Z Mod | :x: | :x: | :x: | :heavy_check_mark: |
 | chrisrgonzales | [270° Front Panel Hinge](./chrisrgonzales/270_degree_hinge) | Hinges that have 270° of swivel, parametric CAD included | :x: | :x: | :heavy_check_mark: | :x: |
+|claytono|[Fysetc S6 V2 Mount](./claytono/fysetc-s6-v2-mount)| DIN Mount for the Fysetc S6 V2 controller |:x:|:heavy_check_mark:|:heavy_check_mark:|:x:|
+||[Voron 2.4 Extrusion Jig](./claytono/2.4-extrusion-jig)|A jig help align extrusions to get a properly square frame |:x:|:x:|:heavy_check_mark:|:x:|
+||[V0 Zip Tie Skirts](./claytono/v0-zip-tie-skirts)|V0 skirts with small loops added along the top to allow zip tyiing cables to them|:heavy_check_mark:|:x:|:x:|:x:
 | Conqueror433 | [Voron Parts Logo](./conqueror433/Voron_Parts_Logo) | Voron Parts Logo for your back panels, 3D Print or Laser Cut | :x: | :x: | :heavy_check_mark: | :x: |
 |consibonsi | [Y-Mod SW 9mm](./consibonsi/Y-Mod_SW_9mm)| 9mm Y belt mod for SW | :x: |:x: |:x: |:heavy_check_mark:|
 | d3nny | [Filtered Power Plug with RND_165-00057](./d3nny/mains_plug_panel_for_RND_165-00057) | Filtered Power Plug for RND 165-00057 and CAT6-Plug | :x: | :x: | :heavy_check_mark: |:x:|

printer_mods/claytono/fysetc-s6-v2-mount/README.md

@@ -0,0 +1,7 @@
+# Fysetc S6 V2 Mount
+
+![Render of board mount and PCB Din mounts](./render.png)
+
+This is a mount for the Fysetc S6 V2 board that is intended to be used with the V2 PCB DIN mount brackets and should work with any machine with DIN rails.  To use this, print the mount and two of the V2 PCB DIN mounts.  Attach the PCB DIN mounts using M2 self tapping screws.  Attach the Fysetc S6 to the mount using M3 hardware of your choice.  I used 6mm M3 hardware, but 8mm should work fine.  
+
+This mount was designed and tested with the Fysetc S6 V2.0 board, but likely works with the S6 1.2 and F6 boards, since they're documented to have the same footprint.