Bowden tube Guide (#808)

* Create Readme.md

* Add files via upload

* Add files via upload

* Update Readme.md

* Update Readme.md

* Update Readme.md

* Add files via upload

* Update Readme.md

* Update README.md

* Delete Long-Arm.f3d

* Delete Long_Arm.step

* Add files via upload

* Delete Mount.f3d

* Delete Mount.step

* Delete Short_Arm.f3d

* Delete Short_Arm.step

printer_mods/Galvanic/Bowden_Tube_Guide/Readme.md

@@ -0,0 +1,23 @@
+# PTFE Bowden Tube Guide and Canbus Wire Support
+
+## Required Hardware:
+- M3x8 Bolt and M3 T-nut
+- M5x10 Bolt or a M5x8
+- Optional 4mm drill bit for cleaning out bowden tube path 
+
+## About
+
+In my 350 build the PTFE tube kept getting caught so I made this arm to keep it up. The shorter arm works better so I recommend using it instead
+
+## Install
+
+- Drill out bowden guide with 4mm drill bit for a perfect fit (optional)
+- Bolt mount to rear frame with M3x8 and tnut putting the lip at the top
+- Screw arm on with M5x10 (I used a M5x8mm and it works fine) into the plastic allowing the arm to still be able to swivel 
+
+
+
+<img src="IMAGES/Tube_Guide.png">
+<img src="IMAGES/Short.jpg">
+<img src="IMAGES/Tube1.jpg">
+<img src="IMAGES/Dokuu.jpg">

printer_mods/README.md

@@ -160,6 +160,7 @@ like so:
 | FreeformFez | [V1.8 Filtered Power Inlet](./FreeformFez/FilteredPower) | V1.6 Filtered Inlet and Rocker Switch for V1.8 | :x: | :heavy_check_mark: | :x: |:x:|
 | GadgetAngel | [Cricut Voron Logos](./GadgetAngel/Cricut_Voron_Logos) |For any cutting machines or machines that rely on vector graphics and use .svg files. These vectors or .svg files are the Voron Design Logos for the Voron 2.4, Voron SwitchWire, Voron 0.0/0.1. and Trident These .svg files use a minimal amount of anchor points to achieve the vector shapes! | :heavy_check_mark: | :x: | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: |
 |  | [Bed Support Extrusions Alignment Tools](./GadgetAngel/Bed_Support_Alignment_Tools) |The bed support alignment tools will assist in helping align the "bed support extrusions" to the frame. When the alignment tools are placed in all four corners of the Voron Printer's frame the "bed support extrusions" will butt up against these tools so that you can screw the "bed support extrusions" down to the printer's frame in the correct position.|  :x: | :x: | :heavy_check_mark: |  :x: | :x: |
+| Galvanic | [Bowden Tube Guide](Galvanic/Bowden_Tube_Guide)| Bowden tube guide and CANBUS wire support |:x:|:heavy_check_mark:|:heavy_check_mark:|:x:|:heavy_check_mark:|
 | gamebofh | [Laser cut door panels](gamebofh/door-panels)| Files to allow you to create laser cut door panels with some ability to adjust |   | :x: | :grey_question: | :heavy_check_mark: | :grey_question:|
 | gen2ng | [Switchwire LED wire pass through](./gen2eng/z_carriage_stop_pass_through) | Z Carriage Stop modification that makes pass through of wires for the LED light bar clean and easy | :x: | :x: | :x: | :heavy_check_mark: | :x: |
 | geoffreyyoung | [FYSETC SPIDER DIN Bracket](./geoffreyyoung/spider_bracket) | FYSETC SPIDER DIN Bracket | :x: | :heavy_check_mark: | :heavy_check_mark: | :x: |