microswitch pod for V2.4 with JST-XH 4-pin connector mount (#216)

* add my mod

* Update README.md

* Update README.md

* Update README.md

* Update README.md

* update folder

* Update readme.md

* update names again

* initial add

* Update readme.md

* Update readme.md

* Update readme.md

* Update readme.md

* Update readme.md

* Update readme.md

* change camera angle

changed camera angle to 25 degrees instead of 20.  Points it slightly closer to the front of the printer, showing less of the rear of the printer.

* Update readme.md

* Update readme.md

* Update view.png

* update view image

* Update readme.md

* Learned how to do multiple mods at once, deleting this mod and adding to new branch.

* Update README.md

* Update README.md

* Update README.md

* Update README.md

* change naming

* Update readme.md

* Update readme.md

* Update README.md

* Update README.md

printer_mods/BladeScraper-Designs/Microswitch_Pod_With_Conector/readme.md

@@ -0,0 +1,8 @@
+This is a simple modification to the microswitch pod to allow the installation of a JST-XH 4-pin connector.
+
+JST-XH  4-pin connector part number B4B-XH-A(LF)(SN) slides into the hole and there's a small lip to keep it sliding all the way thru.  
+Depending on your tolerances it may be tight enough as is, or you may have to use a bit of CA glue.  You may need to clean up the inside of the slot a bit using a utility knife to get the JST in, as it does involve bridging.
+
+I also slightly increased the size of the screw holes from 1.5mm to 1.7mm as I was having a hard time getting mine screwed down.  
+
+![Microswitch_Pod_With_Connector](img/assembly.png)

printer_mods/README.md

@@ -38,6 +38,7 @@ like so:
 |claytono|[Voron 2.4 Extrusion Jig](./claytono/2.4-extrusion-jig)|A jig help align extrusions to get a properly square frame |:x:|:x:|:heavy_check_mark:|:x:|
 |Badnoob |[Precision AB Drive](./Badnoob/Precision_AB_Drive)|Changes the gearing for the AB drives to improve both resolution and torque, with a strenthened frame. |:grey_question:|:grey_question:|:heavy_check_mark:|:x:|
 | |[Rail Alignment](./Badnoob/Rail_Alignment)|Tools and procedure to properly align the rails in 2.4 and Afterburner|:x:|:x:|:heavy_check_mark:|:x:|
+| BladeScraper-Designs | [Microswitch_Pod_With_Connector](./BladeScraper-Designs/Microswitch_Pod_With_Conector) | Microswitch pod with JST-XH 4-pin connector | :x: |:x: |:heavy_check_mark: | :x:
 |BlueBear|[Deck Panel Backpack](./BlueBear/Deck_Panel_Backpack)|A mounting alternative if you don't want to drill your deck panel | :heavy_check_mark: | :x: | :x: |:x:|
 ||[Clippable Wago 221 Mounts](./BlueBear/Wago_221_mount)|Mounts for Wago 221 to screw or clip-in on 1515 extrusions | :heavy_check_mark: | :x: | :x: |
 ||[Ziptie Mount](./BlueBear/Ziptie_Mount)|Clippable Ziptie hooks for 1515 extrusions| :heavy_check_mark: | :x: | :x: |