Merge pull request #1 from VoronDesign/master

Merge master

.github/PULL_REQUEST_TEMPLATE.md

@@ -1,36 +1,46 @@
 <!--
-Thank you for your interest into contributing to VoronUsers, it's
+Thank you for your interest in contributing to the VoronUsers repository, it is
 highly appreciated!
 
-Please make sure you have ticked all points on this
-checklist:
+**Please make sure the submission conforms to the rules outlined below. PRs which fail
+to conform to the rules below are likely to be rejected.**
 -->
 
-  * [ ] Your mod, firmware config or slicer profile is in the correct 
-    folder.
-  * [ ] Your files are located in a subfolder with your name.
-  * [ ] If submitting STL files, make sure they are not corrupt. To test
-    this open them in slic3r and see if it reports any mesh errors.
-  * [ ] If submitting STL files, make sure they are already oriented for 
-    printing, and scaled properly.
-  * [ ] If submitting firmware configs or slicer profiles make sure they
-    don't contain sensible data (e.g. API keys)
-  * [ ] Your mod, config or profile includes a short Readme.md inside its
-    folder summarizing what the mod accomplishes or what the config/profile
-    includes.
-  * [ ] Your PR modifies the top-level Readme.md to list your mod among the
-    existing ones. Read the top part of the file for instructions how to add
-    your mod to the table.
-  * [ ] If you're submitting mods you have tested them, please remember to 
-    indicate which Voron printer this mod is intended for by updating the
-    compatibility matrixc in the top level Readme.md
+  * [ ] The mod, firmware configuration or slicer profile is in the correct category
+    folder. Printable mods go to `printer_mods/`, firmware configurations
+    go to `firmware_configurations/`, slicer profiles go to `slicer_profiles/`.
+    Create a subfolder with your name, and place the mods in a subfolder with
+    a descriptive name within that folder, e.g.: `/printer_mods/FHeilmann/flux_capacitor`
+  * [ ] Folders names MUST NOT contain spaces. If possible, make sure file names also 
+    do not contain any spaces.
+  * [ ] For each mod, add a small `README.md` file to its folder with a short description
+    of what the mod accomplishes. This readme can be used to add pictures, give assembly
+    instructions or specify a bill of materials if the mod requires additional hardware.
+  * [ ] The PR modifies the top-level `README.md` of the category folder adding the 
+    contribution to the table. Read the top part of the file for instructions on how
+    to do this. Please preserve the alphabetical ordering while adding new rows. Make sure
+    to fill out the compatibility matrix to indicate which versions of the Voron printer
+    the submission is compatible with.
+  * [ ] The mod/configuration/profile has been tested by the person submitting the mod 
+    and/or other Voron users. Make sure to add information about how the mod was tested below. 
+  * [ ] The mod is not merely a slight modification of an official Voron part, configuration 
+    or profile (i.e. an official Voron part with a few mm added or removed or a slicer profile 
+    which only modifies a few values). *(When in doubt, contact one of the admins in the 
+    Voron discord before submitting the PR)*
+  * [ ] Submitted STLs are printable without support. *(If the mod does not meet this criterion
+    join the Voron discord and ask the other users for advice on how to modify the mod such 
+    that it does not require supports)*
+  * [ ] Submitted STL files are not corrupt. *(This can be tested by opening the STL in PrusaSlicer
+    and checking if mesh errors are reported.)*
+  * [ ] Submitted STL files are oriented and scaled properly for printing.
+  * [ ] Submitted firmware configs or slicer profiles contain no sensitive data (e.g. API keys).
 
 <!--
-Describe your PR further using the template provided below. The more 
+Describe the submission further using the template provided below. The more 
 details the better!
 -->
 
-#### What does this PR do?
+#### Which mods/configurations/profiles are added by this PR?
 
 #### How was it tested? 
 

.travis.yml

@@ -9,7 +9,9 @@ cache:
   - travis_cache
 
 before_install:
-  - chmod +x ./travis_scripts/ci-build.sh
   - npm install remark-cli remark-validate-links
 
-script: ./travis_scripts/ci-build.sh
+script:
+  - git clone https://github.com/VoronDesign/GithubScripts.git .github_scripts
+  - /bin/bash ./.github_scripts/travis/ci-build.sh
+

LICENSE.md

@@ -0,0 +1,674 @@
+                    GNU GENERAL PUBLIC LICENSE
+                       Version 3, 29 June 2007
+
+ Copyright (C) 2007 Free Software Foundation, Inc. <https://fsf.org/>
+ Everyone is permitted to copy and distribute verbatim copies
+ of this license document, but changing it is not allowed.
+
+                            Preamble
+
+  The GNU General Public License is a free, copyleft license for
+software and other kinds of works.
+
+  The licenses for most software and other practical works are designed
+to take away your freedom to share and change the works.  By contrast,
+the GNU General Public License is intended to guarantee your freedom to
+share and change all versions of a program--to make sure it remains free
+software for all its users.  We, the Free Software Foundation, use the
+GNU General Public License for most of our software; it applies also to
+any other work released this way by its authors.  You can apply it to
+your programs, too.
+
+  When we speak of free software, we are referring to freedom, not
+price.  Our General Public Licenses are designed to make sure that you
+have the freedom to distribute copies of free software (and charge for
+them if you wish), that you receive source code or can get it if you
+want it, that you can change the software or use pieces of it in new
+free programs, and that you know you can do these things.
+
+  To protect your rights, we need to prevent others from denying you
+these rights or asking you to surrender the rights.  Therefore, you have
+certain responsibilities if you distribute copies of the software, or if
+you modify it: responsibilities to respect the freedom of others.
+
+  For example, if you distribute copies of such a program, whether
+gratis or for a fee, you must pass on to the recipients the same
+freedoms that you received.  You must make sure that they, too, receive
+or can get the source code.  And you must show them these terms so they
+know their rights.
+
+  Developers that use the GNU GPL protect your rights with two steps:
+(1) assert copyright on the software, and (2) offer you this License
+giving you legal permission to copy, distribute and/or modify it.
+
+  For the developers' and authors' protection, the GPL clearly explains
+that there is no warranty for this free software.  For both users' and
+authors' sake, the GPL requires that modified versions be marked as
+changed, so that their problems will not be attributed erroneously to
+authors of previous versions.
+
+  Some devices are designed to deny users access to install or run
+modified versions of the software inside them, although the manufacturer
+can do so.  This is fundamentally incompatible with the aim of
+protecting users' freedom to change the software.  The systematic
+pattern of such abuse occurs in the area of products for individuals to
+use, which is precisely where it is most unacceptable.  Therefore, we
+have designed this version of the GPL to prohibit the practice for those
+products.  If such problems arise substantially in other domains, we
+stand ready to extend this provision to those domains in future versions
+of the GPL, as needed to protect the freedom of users.
+
+  Finally, every program is threatened constantly by software patents.
+States should not allow patents to restrict development and use of
+software on general-purpose computers, but in those that do, we wish to
+avoid the special danger that patents applied to a free program could
+make it effectively proprietary.  To prevent this, the GPL assures that
+patents cannot be used to render the program non-free.
+
+  The precise terms and conditions for copying, distribution and
+modification follow.
+
+                       TERMS AND CONDITIONS
+
+  0. Definitions.
+
+  "This License" refers to version 3 of the GNU General Public License.
+
+  "Copyright" also means copyright-like laws that apply to other kinds of
+works, such as semiconductor masks.
+
+  "The Program" refers to any copyrightable work licensed under this
+License.  Each licensee is addressed as "you".  "Licensees" and
+"recipients" may be individuals or organizations.
+
+  To "modify" a work means to copy from or adapt all or part of the work
+in a fashion requiring copyright permission, other than the making of an
+exact copy.  The resulting work is called a "modified version" of the
+earlier work or a work "based on" the earlier work.
+
+  A "covered work" means either the unmodified Program or a work based
+on the Program.
+
+  To "propagate" a work means to do anything with it that, without
+permission, would make you directly or secondarily liable for
+infringement under applicable copyright law, except executing it on a
+computer or modifying a private copy.  Propagation includes copying,
+distribution (with or without modification), making available to the
+public, and in some countries other activities as well.
+
+  To "convey" a work means any kind of propagation that enables other
+parties to make or receive copies.  Mere interaction with a user through
+a computer network, with no transfer of a copy, is not conveying.
+
+  An interactive user interface displays "Appropriate Legal Notices"
+to the extent that it includes a convenient and prominently visible
+feature that (1) displays an appropriate copyright notice, and (2)
+tells the user that there is no warranty for the work (except to the
+extent that warranties are provided), that licensees may convey the
+work under this License, and how to view a copy of this License.  If
+the interface presents a list of user commands or options, such as a
+menu, a prominent item in the list meets this criterion.
+
+  1. Source Code.
+
+  The "source code" for a work means the preferred form of the work
+for making modifications to it.  "Object code" means any non-source
+form of a work.
+
+  A "Standard Interface" means an interface that either is an official
+standard defined by a recognized standards body, or, in the case of
+interfaces specified for a particular programming language, one that
+is widely used among developers working in that language.
+
+  The "System Libraries" of an executable work include anything, other
+than the work as a whole, that (a) is included in the normal form of
+packaging a Major Component, but which is not part of that Major
+Component, and (b) serves only to enable use of the work with that
+Major Component, or to implement a Standard Interface for which an
+implementation is available to the public in source code form.  A
+"Major Component", in this context, means a major essential component
+(kernel, window system, and so on) of the specific operating system
+(if any) on which the executable work runs, or a compiler used to
+produce the work, or an object code interpreter used to run it.
+
+  The "Corresponding Source" for a work in object code form means all
+the source code needed to generate, install, and (for an executable
+work) run the object code and to modify the work, including scripts to
+control those activities.  However, it does not include the work's
+System Libraries, or general-purpose tools or generally available free
+programs which are used unmodified in performing those activities but
+which are not part of the work.  For example, Corresponding Source
+includes interface definition files associated with source files for
+the work, and the source code for shared libraries and dynamically
+linked subprograms that the work is specifically designed to require,
+such as by intimate data communication or control flow between those
+subprograms and other parts of the work.
+
+  The Corresponding Source need not include anything that users
+can regenerate automatically from other parts of the Corresponding
+Source.
+
+  The Corresponding Source for a work in source code form is that
+same work.
+
+  2. Basic Permissions.
+
+  All rights granted under this License are granted for the term of
+copyright on the Program, and are irrevocable provided the stated
+conditions are met.  This License explicitly affirms your unlimited
+permission to run the unmodified Program.  The output from running a
+covered work is covered by this License only if the output, given its
+content, constitutes a covered work.  This License acknowledges your
+rights of fair use or other equivalent, as provided by copyright law.
+
+  You may make, run and propagate covered works that you do not
+convey, without conditions so long as your license otherwise remains
+in force.  You may convey covered works to others for the sole purpose
+of having them make modifications exclusively for you, or provide you
+with facilities for running those works, provided that you comply with
+the terms of this License in conveying all material for which you do
+not control copyright.  Those thus making or running the covered works
+for you must do so exclusively on your behalf, under your direction
+and control, on terms that prohibit them from making any copies of
+your copyrighted material outside their relationship with you.
+
+  Conveying under any other circumstances is permitted solely under
+the conditions stated below.  Sublicensing is not allowed; section 10
+makes it unnecessary.
+
+  3. Protecting Users' Legal Rights From Anti-Circumvention Law.
+
+  No covered work shall be deemed part of an effective technological
+measure under any applicable law fulfilling obligations under article
+11 of the WIPO copyright treaty adopted on 20 December 1996, or
+similar laws prohibiting or restricting circumvention of such
+measures.
+
+  When you convey a covered work, you waive any legal power to forbid
+circumvention of technological measures to the extent such circumvention
+is effected by exercising rights under this License with respect to
+the covered work, and you disclaim any intention to limit operation or
+modification of the work as a means of enforcing, against the work's
+users, your or third parties' legal rights to forbid circumvention of
+technological measures.
+
+  4. Conveying Verbatim Copies.
+
+  You may convey verbatim copies of the Program's source code as you
+receive it, in any medium, provided that you conspicuously and
+appropriately publish on each copy an appropriate copyright notice;
+keep intact all notices stating that this License and any
+non-permissive terms added in accord with section 7 apply to the code;
+keep intact all notices of the absence of any warranty; and give all
+recipients a copy of this License along with the Program.
+
+  You may charge any price or no price for each copy that you convey,
+and you may offer support or warranty protection for a fee.
+
+  5. Conveying Modified Source Versions.
+
+  You may convey a work based on the Program, or the modifications to
+produce it from the Program, in the form of source code under the
+terms of section 4, provided that you also meet all of these conditions:
+
+    a) The work must carry prominent notices stating that you modified
+    it, and giving a relevant date.
+
+    b) The work must carry prominent notices stating that it is
+    released under this License and any conditions added under section
+    7.  This requirement modifies the requirement in section 4 to
+    "keep intact all notices".
+
+    c) You must license the entire work, as a whole, under this
+    License to anyone who comes into possession of a copy.  This
+    License will therefore apply, along with any applicable section 7
+    additional terms, to the whole of the work, and all its parts,
+    regardless of how they are packaged.  This License gives no
+    permission to license the work in any other way, but it does not
+    invalidate such permission if you have separately received it.
+
+    d) If the work has interactive user interfaces, each must display
+    Appropriate Legal Notices; however, if the Program has interactive
+    interfaces that do not display Appropriate Legal Notices, your
+    work need not make them do so.
+
+  A compilation of a covered work with other separate and independent
+works, which are not by their nature extensions of the covered work,
+and which are not combined with it such as to form a larger program,
+in or on a volume of a storage or distribution medium, is called an
+"aggregate" if the compilation and its resulting copyright are not
+used to limit the access or legal rights of the compilation's users
+beyond what the individual works permit.  Inclusion of a covered work
+in an aggregate does not cause this License to apply to the other
+parts of the aggregate.
+
+  6. Conveying Non-Source Forms.
+
+  You may convey a covered work in object code form under the terms
+of sections 4 and 5, provided that you also convey the
+machine-readable Corresponding Source under the terms of this License,
+in one of these ways:
+
+    a) Convey the object code in, or embodied in, a physical product
+    (including a physical distribution medium), accompanied by the
+    Corresponding Source fixed on a durable physical medium
+    customarily used for software interchange.
+
+    b) Convey the object code in, or embodied in, a physical product
+    (including a physical distribution medium), accompanied by a
+    written offer, valid for at least three years and valid for as
+    long as you offer spare parts or customer support for that product
+    model, to give anyone who possesses the object code either (1) a
+    copy of the Corresponding Source for all the software in the
+    product that is covered by this License, on a durable physical
+    medium customarily used for software interchange, for a price no
+    more than your reasonable cost of physically performing this
+    conveying of source, or (2) access to copy the
+    Corresponding Source from a network server at no charge.
+
+    c) Convey individual copies of the object code with a copy of the
+    written offer to provide the Corresponding Source.  This
+    alternative is allowed only occasionally and noncommercially, and
+    only if you received the object code with such an offer, in accord
+    with subsection 6b.
+
+    d) Convey the object code by offering access from a designated
+    place (gratis or for a charge), and offer equivalent access to the
+    Corresponding Source in the same way through the same place at no
+    further charge.  You need not require recipients to copy the
+    Corresponding Source along with the object code.  If the place to
+    copy the object code is a network server, the Corresponding Source
+    may be on a different server (operated by you or a third party)
+    that supports equivalent copying facilities, provided you maintain
+    clear directions next to the object code saying where to find the
+    Corresponding Source.  Regardless of what server hosts the
+    Corresponding Source, you remain obligated to ensure that it is
+    available for as long as needed to satisfy these requirements.
+
+    e) Convey the object code using peer-to-peer transmission, provided
+    you inform other peers where the object code and Corresponding
+    Source of the work are being offered to the general public at no
+    charge under subsection 6d.
+
+  A separable portion of the object code, whose source code is excluded
+from the Corresponding Source as a System Library, need not be
+included in conveying the object code work.
+
+  A "User Product" is either (1) a "consumer product", which means any
+tangible personal property which is normally used for personal, family,
+or household purposes, or (2) anything designed or sold for incorporation
+into a dwelling.  In determining whether a product is a consumer product,
+doubtful cases shall be resolved in favor of coverage.  For a particular
+product received by a particular user, "normally used" refers to a
+typical or common use of that class of product, regardless of the status
+of the particular user or of the way in which the particular user
+actually uses, or expects or is expected to use, the product.  A product
+is a consumer product regardless of whether the product has substantial
+commercial, industrial or non-consumer uses, unless such uses represent
+the only significant mode of use of the product.
+
+  "Installation Information" for a User Product means any methods,
+procedures, authorization keys, or other information required to install
+and execute modified versions of a covered work in that User Product from
+a modified version of its Corresponding Source.  The information must
+suffice to ensure that the continued functioning of the modified object
+code is in no case prevented or interfered with solely because
+modification has been made.
+
+  If you convey an object code work under this section in, or with, or
+specifically for use in, a User Product, and the conveying occurs as
+part of a transaction in which the right of possession and use of the
+User Product is transferred to the recipient in perpetuity or for a
+fixed term (regardless of how the transaction is characterized), the
+Corresponding Source conveyed under this section must be accompanied
+by the Installation Information.  But this requirement does not apply
+if neither you nor any third party retains the ability to install
+modified object code on the User Product (for example, the work has
+been installed in ROM).
+
+  The requirement to provide Installation Information does not include a
+requirement to continue to provide support service, warranty, or updates
+for a work that has been modified or installed by the recipient, or for
+the User Product in which it has been modified or installed.  Access to a
+network may be denied when the modification itself materially and
+adversely affects the operation of the network or violates the rules and
+protocols for communication across the network.
+
+  Corresponding Source conveyed, and Installation Information provided,
+in accord with this section must be in a format that is publicly
+documented (and with an implementation available to the public in
+source code form), and must require no special password or key for
+unpacking, reading or copying.
+
+  7. Additional Terms.
+
+  "Additional permissions" are terms that supplement the terms of this
+License by making exceptions from one or more of its conditions.
+Additional permissions that are applicable to the entire Program shall
+be treated as though they were included in this License, to the extent
+that they are valid under applicable law.  If additional permissions
+apply only to part of the Program, that part may be used separately
+under those permissions, but the entire Program remains governed by
+this License without regard to the additional permissions.
+
+  When you convey a copy of a covered work, you may at your option
+remove any additional permissions from that copy, or from any part of
+it.  (Additional permissions may be written to require their own
+removal in certain cases when you modify the work.)  You may place
+additional permissions on material, added by you to a covered work,
+for which you have or can give appropriate copyright permission.
+
+  Notwithstanding any other provision of this License, for material you
+add to a covered work, you may (if authorized by the copyright holders of
+that material) supplement the terms of this License with terms:
+
+    a) Disclaiming warranty or limiting liability differently from the
+    terms of sections 15 and 16 of this License; or
+
+    b) Requiring preservation of specified reasonable legal notices or
+    author attributions in that material or in the Appropriate Legal
+    Notices displayed by works containing it; or
+
+    c) Prohibiting misrepresentation of the origin of that material, or
+    requiring that modified versions of such material be marked in
+    reasonable ways as different from the original version; or
+
+    d) Limiting the use for publicity purposes of names of licensors or
+    authors of the material; or
+
+    e) Declining to grant rights under trademark law for use of some
+    trade names, trademarks, or service marks; or
+
+    f) Requiring indemnification of licensors and authors of that
+    material by anyone who conveys the material (or modified versions of
+    it) with contractual assumptions of liability to the recipient, for
+    any liability that these contractual assumptions directly impose on
+    those licensors and authors.
+
+  All other non-permissive additional terms are considered "further
+restrictions" within the meaning of section 10.  If the Program as you
+received it, or any part of it, contains a notice stating that it is
+governed by this License along with a term that is a further
+restriction, you may remove that term.  If a license document contains
+a further restriction but permits relicensing or conveying under this
+License, you may add to a covered work material governed by the terms
+of that license document, provided that the further restriction does
+not survive such relicensing or conveying.
+
+  If you add terms to a covered work in accord with this section, you
+must place, in the relevant source files, a statement of the
+additional terms that apply to those files, or a notice indicating
+where to find the applicable terms.
+
+  Additional terms, permissive or non-permissive, may be stated in the
+form of a separately written license, or stated as exceptions;
+the above requirements apply either way.
+
+  8. Termination.
+
+  You may not propagate or modify a covered work except as expressly
+provided under this License.  Any attempt otherwise to propagate or
+modify it is void, and will automatically terminate your rights under
+this License (including any patent licenses granted under the third
+paragraph of section 11).
+
+  However, if you cease all violation of this License, then your
+license from a particular copyright holder is reinstated (a)
+provisionally, unless and until the copyright holder explicitly and
+finally terminates your license, and (b) permanently, if the copyright
+holder fails to notify you of the violation by some reasonable means
+prior to 60 days after the cessation.
+
+  Moreover, your license from a particular copyright holder is
+reinstated permanently if the copyright holder notifies you of the
+violation by some reasonable means, this is the first time you have
+received notice of violation of this License (for any work) from that
+copyright holder, and you cure the violation prior to 30 days after
+your receipt of the notice.
+
+  Termination of your rights under this section does not terminate the
+licenses of parties who have received copies or rights from you under
+this License.  If your rights have been terminated and not permanently
+reinstated, you do not qualify to receive new licenses for the same
+material under section 10.
+
+  9. Acceptance Not Required for Having Copies.
+
+  You are not required to accept this License in order to receive or
+run a copy of the Program.  Ancillary propagation of a covered work
+occurring solely as a consequence of using peer-to-peer transmission
+to receive a copy likewise does not require acceptance.  However,
+nothing other than this License grants you permission to propagate or
+modify any covered work.  These actions infringe copyright if you do
+not accept this License.  Therefore, by modifying or propagating a
+covered work, you indicate your acceptance of this License to do so.
+
+  10. Automatic Licensing of Downstream Recipients.
+
+  Each time you convey a covered work, the recipient automatically
+receives a license from the original licensors, to run, modify and
+propagate that work, subject to this License.  You are not responsible
+for enforcing compliance by third parties with this License.
+
+  An "entity transaction" is a transaction transferring control of an
+organization, or substantially all assets of one, or subdividing an
+organization, or merging organizations.  If propagation of a covered
+work results from an entity transaction, each party to that
+transaction who receives a copy of the work also receives whatever
+licenses to the work the party's predecessor in interest had or could
+give under the previous paragraph, plus a right to possession of the
+Corresponding Source of the work from the predecessor in interest, if
+the predecessor has it or can get it with reasonable efforts.
+
+  You may not impose any further restrictions on the exercise of the
+rights granted or affirmed under this License.  For example, you may
+not impose a license fee, royalty, or other charge for exercise of
+rights granted under this License, and you may not initiate litigation
+(including a cross-claim or counterclaim in a lawsuit) alleging that
+any patent claim is infringed by making, using, selling, offering for
+sale, or importing the Program or any portion of it.
+
+  11. Patents.
+
+  A "contributor" is a copyright holder who authorizes use under this
+License of the Program or a work on which the Program is based.  The
+work thus licensed is called the contributor's "contributor version".
+
+  A contributor's "essential patent claims" are all patent claims
+owned or controlled by the contributor, whether already acquired or
+hereafter acquired, that would be infringed by some manner, permitted
+by this License, of making, using, or selling its contributor version,
+but do not include claims that would be infringed only as a
+consequence of further modification of the contributor version.  For
+purposes of this definition, "control" includes the right to grant
+patent sublicenses in a manner consistent with the requirements of
+this License.
+
+  Each contributor grants you a non-exclusive, worldwide, royalty-free
+patent license under the contributor's essential patent claims, to
+make, use, sell, offer for sale, import and otherwise run, modify and
+propagate the contents of its contributor version.
+
+  In the following three paragraphs, a "patent license" is any express
+agreement or commitment, however denominated, not to enforce a patent
+(such as an express permission to practice a patent or covenant not to
+sue for patent infringement).  To "grant" such a patent license to a
+party means to make such an agreement or commitment not to enforce a
+patent against the party.
+
+  If you convey a covered work, knowingly relying on a patent license,
+and the Corresponding Source of the work is not available for anyone
+to copy, free of charge and under the terms of this License, through a
+publicly available network server or other readily accessible means,
+then you must either (1) cause the Corresponding Source to be so
+available, or (2) arrange to deprive yourself of the benefit of the
+patent license for this particular work, or (3) arrange, in a manner
+consistent with the requirements of this License, to extend the patent
+license to downstream recipients.  "Knowingly relying" means you have
+actual knowledge that, but for the patent license, your conveying the
+covered work in a country, or your recipient's use of the covered work
+in a country, would infringe one or more identifiable patents in that
+country that you have reason to believe are valid.
+
+  If, pursuant to or in connection with a single transaction or
+arrangement, you convey, or propagate by procuring conveyance of, a
+covered work, and grant a patent license to some of the parties
+receiving the covered work authorizing them to use, propagate, modify
+or convey a specific copy of the covered work, then the patent license
+you grant is automatically extended to all recipients of the covered
+work and works based on it.
+
+  A patent license is "discriminatory" if it does not include within
+the scope of its coverage, prohibits the exercise of, or is
+conditioned on the non-exercise of one or more of the rights that are
+specifically granted under this License.  You may not convey a covered
+work if you are a party to an arrangement with a third party that is
+in the business of distributing software, under which you make payment
+to the third party based on the extent of your activity of conveying
+the work, and under which the third party grants, to any of the
+parties who would receive the covered work from you, a discriminatory
+patent license (a) in connection with copies of the covered work
+conveyed by you (or copies made from those copies), or (b) primarily
+for and in connection with specific products or compilations that
+contain the covered work, unless you entered into that arrangement,
+or that patent license was granted, prior to 28 March 2007.
+
+  Nothing in this License shall be construed as excluding or limiting
+any implied license or other defenses to infringement that may
+otherwise be available to you under applicable patent law.
+
+  12. No Surrender of Others' Freedom.
+
+  If conditions are imposed on you (whether by court order, agreement or
+otherwise) that contradict the conditions of this License, they do not
+excuse you from the conditions of this License.  If you cannot convey a
+covered work so as to satisfy simultaneously your obligations under this
+License and any other pertinent obligations, then as a consequence you may
+not convey it at all.  For example, if you agree to terms that obligate you
+to collect a royalty for further conveying from those to whom you convey
+the Program, the only way you could satisfy both those terms and this
+License would be to refrain entirely from conveying the Program.
+
+  13. Use with the GNU Affero General Public License.
+
+  Notwithstanding any other provision of this License, you have
+permission to link or combine any covered work with a work licensed
+under version 3 of the GNU Affero General Public License into a single
+combined work, and to convey the resulting work.  The terms of this
+License will continue to apply to the part which is the covered work,
+but the special requirements of the GNU Affero General Public License,
+section 13, concerning interaction through a network will apply to the
+combination as such.
+
+  14. Revised Versions of this License.
+
+  The Free Software Foundation may publish revised and/or new versions of
+the GNU General Public License from time to time.  Such new versions will
+be similar in spirit to the present version, but may differ in detail to
+address new problems or concerns.
+
+  Each version is given a distinguishing version number.  If the
+Program specifies that a certain numbered version of the GNU General
+Public License "or any later version" applies to it, you have the
+option of following the terms and conditions either of that numbered
+version or of any later version published by the Free Software
+Foundation.  If the Program does not specify a version number of the
+GNU General Public License, you may choose any version ever published
+by the Free Software Foundation.
+
+  If the Program specifies that a proxy can decide which future
+versions of the GNU General Public License can be used, that proxy's
+public statement of acceptance of a version permanently authorizes you
+to choose that version for the Program.
+
+  Later license versions may give you additional or different
+permissions.  However, no additional obligations are imposed on any
+author or copyright holder as a result of your choosing to follow a
+later version.
+
+  15. Disclaimer of Warranty.
+
+  THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY
+APPLICABLE LAW.  EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT
+HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY
+OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO,
+THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
+PURPOSE.  THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM
+IS WITH YOU.  SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF
+ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
+
+  16. Limitation of Liability.
+
+  IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING
+WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MODIFIES AND/OR CONVEYS
+THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY
+GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE
+USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF
+DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD
+PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS),
+EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF
+SUCH DAMAGES.
+
+  17. Interpretation of Sections 15 and 16.
+
+  If the disclaimer of warranty and limitation of liability provided
+above cannot be given local legal effect according to their terms,
+reviewing courts shall apply local law that most closely approximates
+an absolute waiver of all civil liability in connection with the
+Program, unless a warranty or assumption of liability accompanies a
+copy of the Program in return for a fee.
+
+                     END OF TERMS AND CONDITIONS
+
+            How to Apply These Terms to Your New Programs
+
+  If you develop a new program, and you want it to be of the greatest
+possible use to the public, the best way to achieve this is to make it
+free software which everyone can redistribute and change under these terms.
+
+  To do so, attach the following notices to the program.  It is safest
+to attach them to the start of each source file to most effectively
+state the exclusion of warranty; and each file should have at least
+the "copyright" line and a pointer to where the full notice is found.
+
+    <one line to give the program's name and a brief idea of what it does.>
+    Copyright (C) <year>  <name of author>
+
+    This program is free software: you can redistribute it and/or modify
+    it under the terms of the GNU General Public License as published by
+    the Free Software Foundation, either version 3 of the License, or
+    (at your option) any later version.
+
+    This program is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+    GNU General Public License for more details.
+
+    You should have received a copy of the GNU General Public License
+    along with this program.  If not, see <https://www.gnu.org/licenses/>.
+
+Also add information on how to contact you by electronic and paper mail.
+
+  If the program does terminal interaction, make it output a short
+notice like this when it starts in an interactive mode:
+
+    <program>  Copyright (C) <year>  <name of author>
+    This program comes with ABSOLUTELY NO WARRANTY; for details type `show w'.
+    This is free software, and you are welcome to redistribute it
+    under certain conditions; type `show c' for details.
+
+The hypothetical commands `show w' and `show c' should show the appropriate
+parts of the General Public License.  Of course, your program's commands
+might be different; for a GUI interface, you would use an "about box".
+
+  You should also get your employer (if you work as a programmer) or school,
+if any, to sign a "copyright disclaimer" for the program, if necessary.
+For more information on this, and how to apply and follow the GNU GPL, see
+<https://www.gnu.org/licenses/>.
+
+  The GNU General Public License does not permit incorporating your program
+into proprietary programs.  If your program is a subroutine library, you
+may consider it more useful to permit linking proprietary applications with
+the library.  If this is what you want to do, use the GNU Lesser General
+Public License instead of this License.  But first, please read
+<https://www.gnu.org/licenses/why-not-lgpl.html>.

firmware_configurations/README.md

@@ -24,6 +24,7 @@ If your mod is lacking a column in the compatibility matrix, feel free to submit
 | Creator | Config title | Description | V1.6 | V2.1 | V2.2 |
 |---------|--------------|-------------|------|------|------|
 | Chron   | [SKR 1.3 TMC2208 UART Config](./klipper/Chron) | Configuration for SKR 1.3 TMC2208 UART | :x: | :heavy_check_mark: | :grey_question: |
-| Danowar  | [FYSETC F6 1.3 Klipper Config](./klipper/Danowar/FYSETC_F6_V1.3_Klipper_Config) | Klipper config for a FYSETC F6 350 build. | :x: | :heavy_check_mark: | :grey_question: |
+| Danowar  | [FYSETC F6 1.3 Klipper Config](./klipper/Danowar/FYSETC_F6_V1.3_Klipper_Config) | Klipper config for a FYSETC F6 350 build. UPDATED 11/14/19 | :x: | :heavy_check_mark: | :heavy_check_mark: |
+| eddie  | [SKR 1.3 V2 Universal Config](./klipper/eddie) | Universal Config and Setup Guide for SKR 1.3 and V2 | :x: | :heavy_check_mark: | :heavy_check_mark: |
 
 ---

firmware_configurations/klipper/Danowar/FYSETC_F6_V1.3_Klipper_Config/printer.cfg

@@ -90,9 +90,9 @@ enable_pin: !ar56
 step_distance: 0.0125
 # connected to ymax on mcu_xye
 endstop_pin: ^!ar15
-position_min: -11
-position_endstop: 339
-position_max: 339
+position_min: 0
+position_endstop: 350
+position_max: 350
 homing_speed: 100
 homing_retract_dist: 5
 homing_positive_dir: true
@@ -100,17 +100,18 @@ homing_positive_dir: true
 [stepper_z]
 # connected to X on mcu_z (Front Left Stepper, from top)
 step_pin: z:ar54
-dir_pin: z:ar55
+dir_pin: !z:ar55
 enable_pin: !z:ar38
 # 1.8deg - 400 steps per mm
 step_distance: 0.00250
 # connected to zmax on mcu_z
-endstop_pin: !z:ar12
+endstop_pin: ^!z:ar12
 
 # offset for nozzle to bed off z switch
-position_endstop: 1.84 ;ABS
-position_max: 340
-position_min: -1
+# position_endstop: 1.63 ;ABS   ---FSR
+position_endstop: 0.12
+position_max: 335
+position_min: -5
 homing_speed: 15.0
 second_homing_speed: 3.0
 homing_retract_dist: 3.0
@@ -119,7 +120,7 @@ homing_positive_dir: false
 [stepper_z1]
 # connected to Y on mcu_z (Rear Left Stepper, from top)
 step_pin: z:ar60
-dir_pin: !z:ar61
+dir_pin: z:ar61
 enable_pin: !z:ar56
 # 1.8deg - 400 steps per mm
 step_distance: 0.00250
@@ -127,7 +128,7 @@ step_distance: 0.00250
 [stepper_z2]
 # connected to Z on mcu_z (Rear Right Stepper, from top)
 step_pin: z:ar43
-dir_pin: z:ar48
+dir_pin: !z:ar48
 enable_pin: !z:ar58
 # 1.8deg - 400 steps per mm
 step_distance: 0.00250
@@ -135,7 +136,7 @@ step_distance: 0.00250
 [stepper_z3]
 # connected to E0 on mcu_z (Front Right Stepper, from top)
 step_pin: z:ar26
-dir_pin: !z:ar28
+dir_pin: z:ar28
 enable_pin: !z:ar24
 # 1.8deg - 400 steps per mm
 step_distance: 0.00250
@@ -144,6 +145,7 @@ step_distance: 0.00250
 # ar71 not in pin map, using actual pin number
 uart_pin: PG3
 microsteps: 16
+interpolate: False
 run_current: 1.0
 hold_current: 0.6
 
@@ -151,6 +153,7 @@ hold_current: 0.6
 # ar73 not in pin map, using actual pin number
 uart_pin: PJ3
 microsteps: 16
+interpolate: False
 run_current: 1.0
 hold_current: 0.6
 
@@ -158,6 +161,15 @@ hold_current: 0.6
 # ar76 not in pin map, using actual pin number
 uart_pin: PJ5
 microsteps: 16
+interpolate: False
+run_current: 0.8
+hold_current: 0.2
+
+[tmc2208 extruder1]
+# ar80 not in pin map, using actual pin number
+uart_pin: PE7
+microsteps: 16
+interpolate: False
 run_current: 0.8
 hold_current: 0.2
 
@@ -165,6 +177,7 @@ hold_current: 0.2
 # z:ar71 not in pin map, using actual pin number
 uart_pin: z:PG3
 microsteps: 16
+interpolate: False
 run_current: 0.8
 hold_current: 0.6
 
@@ -172,6 +185,7 @@ hold_current: 0.6
 # z:ar73 not in pin map, using actual pin number
 uart_pin: z:PJ3
 microsteps: 16
+interpolate: False
 run_current: 0.8
 hold_current: 0.6
 
@@ -179,6 +193,7 @@ hold_current: 0.6
 # z:ar78 not in pin map, using actual pin number
 uart_pin: z:PE2
 microsteps: 16
+interpolate: False
 run_current: 0.8
 hold_current: 0.6
 
@@ -186,12 +201,13 @@ hold_current: 0.6
 # z:ar76 not in pin map, using actual pin number
 uart_pin: z:PJ5
 microsteps: 16
+interpolate: False
 run_current: 0.8
 hold_current: 0.6
 
-#	used to force a single stepper to move.  not used once setup
-[force_move]
-enable_force_move: true
+# #	used to force a single stepper to move.  not used once setup
+# [force_move]
+# enable_force_move: true
 
 # Probe
 [probe]
@@ -199,45 +215,56 @@ enable_force_move: true
 pin: ^!z:ar2
 x_offset: 0.0
 # offset for inductive probe y direction off nozzle
-y_offset: 25.0
+y_offset: 30.0
 # offset for inductive probe in z height
 z_offset: 0.00
-speed: 2
+speed: 10
+samples: 1
+sample_retract_dist: 2.0
 
 #	this is required for gantry leveling and replaces your G28 command
 #	with the gcode used here.  Used to home X/Y/Z with mechanical switches
 [homing_override]
 set_position_z: 0
 gcode:
+    BED_MESH_CLEAR
 	G90
 	G0 Z15 F600
 	G28 X Y
     #	For the FSR Switch
-	G0 X227 Y-11 F3000
+	G0 X225 Y350 F5000
 	G28 Z
-	G0 Z10 F3000
-	#   Clean nozzle then rezero z
+	G0 Z13 F2000
+    # level gantry
+    quad_gantry_level
+    #   Clean nozzle then rezero z
     nozzle_clean
-    G0 X227 Y-11 F3000
+    G0 X225 Y350 F5000
 	G28 Z
-	G0 Z10 F3000
+	G0 Z13 F2000
     #G0 X175 Y170 Z10 F3000
  
 #	gantry_level is to put a moving gantry into plan with
 #	a fixed bed.  Must have 4 steppers on the gantry
 [quad_gantry_level]
 gantry_corners:
-	-46,-12
-	416,396
+	-59,0
+	409,421
 points:
-	80,60
-	80,250
-	270,250
-	270,60
-speed: 100
-horizontal_move_z: 10
-samples: 1
-sample_retract_dist: 2.0
+	30,0
+	30,280
+	320,280
+	320,0
+# points:
+	# 100,80
+	# 100,230
+	# 250,230
+	# 250,80
+speed: 300
+horizontal_move_z: 8
+retries: 5
+retry_tolerance: 0.01
+max_adjust: 8
  
 [extruder]
 # connected to E0 on mcu_xye
@@ -249,11 +276,13 @@ step_distance: 0.001803
 nozzle_diameter: 0.400
 	
 # PA can be disabled by declaring a 0.0 value
-pressure_advance: 0.15
+pressure_advance: 0.0
+#pressure_advance: 0.15
 # time seconds to look ahead for PA moves default is 0.010 or 10ms
 pressure_advance_lookahead_time: 0.030
 filament_diameter: 1.750
-max_extrude_only_distance: 800.0
+max_extrude_only_distance: 1000.0
+max_extrude_cross_section: 1000.0
 
 # connected to E0 OUT on mcu_xye	
 heater_pin: ar5
@@ -265,14 +294,33 @@ sensor_pin: analog12
 smooth_time: 3.0
 max_power: 1.0
 # PID for 230C
-control: pid
-pid_Kp: 20.097
-pid_Ki: 0.950
-pid_Kd: 106.265
+#control: pid
+#pid_Kp: 28.263
+#pid_Ki: 1.942
+#pid_Kd: 102.808
 min_extrude_temp: 0
 min_temp: 0
 max_temp: 300
 
+[extruder1]
+# connected to E1 on mcu_xye
+step_pin: ar36
+dir_pin: ar34
+enable_pin: !ar30
+# 1.8deg - 555 steps per mm - 1/16 microstepping -  M2
+step_distance: 0.001803
+nozzle_diameter: 0.400
+	
+# PA can be disabled by declaring a 0.0 value
+pressure_advance: 0.0
+#pressure_advance: 0.15
+# time seconds to look ahead for PA moves default is 0.010 or 10ms
+pressure_advance_lookahead_time: 0.030
+filament_diameter: 1.750
+max_extrude_only_distance: 1000.0
+max_extrude_cross_section: 1000.0
+shared_heater: extruder
+
 #	thermally controlled hotend fan
 [heater_fan my_nozzle_fan]
 # connected to FAN0 on mcu_z
@@ -283,39 +331,27 @@ heater: extruder
 heater_temp: 50.0
 fan_speed: 1   
 
-# #	thermally controlled electronics bay cooling fans
-# [heater_fan cpu_fan]
-# # connected to FAN2 on mcu_xye
-# pin: ar46
-# max_power: 1.0
-# kick_start_time: 0.500
-# heater: extruder
-# heater_temp: 50.0
-# fan_speed: 1  
-
-#	manually controlled electronics bay cooling fans
-[output_pin cpu_fan]
+#	thermally controlled electronics bay cooling fans
+[heater_fan cpu_fan]
 # connected to FAN2 on mcu_xye
 pin: ar46
-pwm: True
-value: 1
-shutdown_value: 0
+max_power: 1.0
+kick_start_time: 0.500
+heater: extruder
+heater_temp: 50.0
+fan_speed: 1  
 
-#	manually controlled stepstick cooling fans
-[output_pin z_driver_fan]
-# connected to FAN1 on mcu_z
-pin: z:ar45
-pwm: True
-value: 1
-shutdown_value: 0
+#	stepstick cooling fans
+[multi_pin driver_fans]
+# connected to FAN1 on each mcu
+pins: z:ar45, ar45
 
-#	manually controlled stepstick cooling fans
-[output_pin xye_driver_fan]
-# connected to FAN1 on mcu_exy
-pin: ar45
-pwm: True
-value: 1
-shutdown_value: 0
+[controller_fan CPU_Fans]
+pin: multi_pin:driver_fans
+max_power: .5
+heater: extruder, heater_bed
+cycle_time: 0.010
+hardware_pwm: True
 
 #	manually controlled chamber exhaust (SET_PIN PIN=chamber_fan VALUE=1)
 [output_pin chamber_fan]
@@ -324,6 +360,18 @@ pin: z:ar46
 pwm: True
 value: 0
 shutdown_value: 0
+cycle_time: 0.010
+hardware_pwm: True
+
+#	manually controlled hotend light (SET_PIN PIN=hotend_light VALUE=1)
+[output_pin HOTEND_LIGHT]
+# connected to HEATER1 on mcu_xye
+pin: ar6
+pwm: True
+value: 0.5
+shutdown_value: 0
+cycle_time: 0.010
+hardware_pwm: True
  
 #	bed heater configuration 
 [heater_bed]
@@ -349,7 +397,8 @@ max_temp: 120
 # connected to FAN0 on mcu_xye
 pin: ar44
 max_power: 1.0
-kick_start_time: 0.500
+kick_start_time: 1.00
+hardware_pwm: true
 
 [printer]
 # settings below are the max and can't be commanded over in gcode
@@ -369,6 +418,19 @@ square_corner_velocity: 10.0
 #   cornering velocity. If this is set to zero then the toolhead will
 #   decelerate to zero at each corner. The default is 5mm/s.
 
+[bed_mesh]
+speed: 100
+horizontal_move_z: 10
+min_point: 25,0
+max_point: 325,295
+probe_count: 7,7
+fade_end: 10
+split_delta_z: .01
+move_check_distance: 3
+mesh_pps: 2,2
+algorithm: lagrange
+relative_reference_index: 24
+
 [idle_timeout]
 # high motor off time so I don't have to relevel gantry often
 timeout: 600000
@@ -380,9 +442,7 @@ timeout: 600000
 [gcode_macro g32]
 gcode:
 	G28
-	quad_gantry_level
-    quad_gantry_level
-    quad_gantry_level
+	#quad_gantry_level
     
 	
 #	macro to level the gantry.  use G32 in the terminal to call
@@ -400,43 +460,31 @@ gcode:
 #    change for your starting scripting needs
 [gcode_macro print_start]
 gcode:
-	#G21  ; set units to mm
-	#G90  ; use absolute coordinates
-	#T0  ; select tool 0
-	#G92 E0.0  ; reset e count
-	#M220 S100 ; reset speed multiplier
-    
-    #M140 S[first_layer_bed_temperature]  ; set bed temperature and do not wait
-    #M109 S190                            ; set print head temperature and wait
-    #M190 S[first_layer_bed_temperature]  ; set bed temperature and wait
-    
-    G28 ; home printer
-    quad_gantry_level ; final level check
-    #G28 ; home printer
-    G28 Z ; rehome just z after gantry level
-	G0 Z10 F3000
-    G0 X175 Y170 F3000
+	G28 ; home printer
+    G91
+    G1 E15.00 F1000
+    G90
+    G0 X175 Y170 Z10 F3000
  
 
 #    Use print_end for you slicer ending script    
 [gcode_macro print_end]
 gcode:
 	G91  							;relative positioning
-	G1 E-5.00 F1000  				;retract 5mm of filament
+	G1 E-15.00 F1000  				;retract 5mm of filament
 	G1 Z+1.00 X-20.0 Y-20.0 F20000  ;short quick move to disengage from print
 	G1 Z+10.00  F20000  			;move Z-Axis 10mm away from part
 
-	G90  				;absolute positioning
-	G1 X350 Y339  		; move to back corner
-
-	#G91  				; relative positioning
-	#G1 E-8.00 F500  	;retract additional filament to prevent oozing
-    #G90 				;absolute positioning
-	
-	M104 S0  			;turn off hotend
-	M140 S0  			;turn off heatbed
-	M106 S0  			; shut off blower
+	G90  			            	;absolute positioning
+	G1 X350 Y339  	            	; move to back corner
 
+    M104 S0 T0                      ;turn off hotend
+	M104 S0 T1                      ;turn off hotend
+	M104 S0                         ;turn off hotend
+    M140 S0  			            ;turn off heatbed
+	M106 S0  			            ; shut off blower
+    T0
+    
 #	Set Temps for ABS Warmup
 [gcode_macro abs_warmup_temp]
 gcode:
@@ -452,33 +500,66 @@ gcode:
 [gcode_macro nozzle_clean]
 gcode:
 	G1 Z10 F3000				;lift nozzle 25mm
-	G1 X80 Y-4 F7500			;move to nozzle brush
-	G1 Z5 F3000				    ;move nozzle into brush
-	G1 X120 Y-11 F6000			;scrub
-	G1 X80 Y-4 F6000			;scrub
-	G1 Y-11 F6000			    ;move
-	G1 X120 Y-4 F6000			;scrub
-	G1 X80 Y-11 F6000			;scrub
-	G1 Y-4 F6000		    	;move
-	G1 X120 Y-11 F6000			;scrub
-	G1 X80 Y-4 F6000			;scrub
-	G1 Y-11 F6000			    ;move
-	G1 X120 Y-4 F6000			;scrub
-	G1 X80 Y-11 F6000			;scrub
-	G1 Y-4 F6000		    	;move
-    G1 Z10 F3000			    ;lift z 10mm
+	G1 X70 Y350 F9000			;move to nozzle brush
+	G1 Z1 F3000				    ;move nozzle into brush
+	G1 X135 F9000   			;scrub
+	G1 X70 F9000	    		;scrub
+	G1 X135 F9000   			;scrub
+	G1 X70 F9000	    		;scrub
+	G1 X135 F9000   			;scrub
+	G1 X70 F9000	    		;scrub
+	G1 X135 F9000   			;scrub
+	G1 Z10 F3000			    ;lift z 10mm
 	#G1 X175 Y170	F9000		;move nozzle to center
-	
+
+#	Tool 0 Filament Load - Only runs when hot
+[gcode_macro load_primary]
+gcode:
+    {% if printer.extruder0.temperature > 185 %}
+        G91
+        G1 E825 F10000
+        G1 E15 F150
+        G90
+    {% endif %}    
+    
+#	Tool 0 Filament Unload - Only runs when hot
+[gcode_macro unload_primary]
+gcode:
+    {% if printer.extruder0.temperature > 185 %}
+        G91
+        G1 E10 F300
+        G1 E-835 F10000
+        G90
+    {% endif %}    
+    
+#	Tool 1 Filament Load - Loads to pre tool change position (-100mm)
+[gcode_macro load_secondary]
+gcode:
+    T1
+    G91
+    G1 E725 F10000
+    G90
+    T0
+
+#	Tool 1 Filament Unload
+[gcode_macro unload_secondary]
+gcode:
+    T1
+    G91
+    G1 E-725 F10000
+    G90
+    T0
+
 #	Macro to Babystep Up 0.02mm
 [gcode_macro babystep_up]
 gcode:
-	SET_GCODE_OFFSET Z_ADJUST=0.02
-
+	SET_GCODE_OFFSET Z_ADJUST=0.02 move=1
+    
 #	Macro to Babystep Down 0.02mm
 [gcode_macro babystep_down]
 gcode:
-	SET_GCODE_OFFSET Z_ADJUST=-0.02
-
+	SET_GCODE_OFFSET Z_ADJUST=-0.02 move=1
+    
 # BED_MESH_CALIBRATE: Perform Mesh Bed Leveling
 # BED_MESH_CLEAR: Clear the Mesh so no z-adjusment is made
 # BED_MESH_MAP: Probe the bed and serialize output
@@ -503,3 +584,9 @@ gcode:
 # STEPPER_BUZZ: Oscillate a given stepper to help id it
 # UNLOAD_FILAMENT: G-Code macro
 # Z_TILT_ADJUST: Adjust the Z tilt
+
+#*# [extruder]
+#*# control = pid
+#*# pid_kp = 23.580
+#*# pid_ki = 1.131
+#*# pid_kd = 122.910

firmware_configurations/klipper/eddie/Readme.md

@@ -0,0 +1,8 @@
+### SKR 1.3 Setup Guide and Documentation
+This setup guide is the result of many contributions from the community. It is meant to take over from where the V2.x structural manual ended and take you through to your first test print and cereal submittal.
+
+Please read the guide carefully, there are many details that seem trivial but are included because of one or more people got stuck at these points. We as a community want to make sure that you have the best experience possible and learn from our mistakes. If you find a something confusing and would like clarification, that likely means someone else in the past or future will also find it difficult. Please reach out to me and I will gladly update the document.
+
+The configuration file is a universal configuration file. This means that it will require some more attention to detail for you to fill out the last 1% of the config file for your specific use case. This is on purpose so that you have a working understanding of the configuration file and know how to solve issues down the road. Paired with the setup guide, you should have (nearly) all the information you need. Please always feel free to reach out if you have any questions or find a mistake, this file lives on Github as a living document so that everyone can keep track of the revisions that have been made!
+
+-eddie

firmware_configurations/klipper/eddie/Voron2_SKR_Universal_Config.cfg

@@ -0,0 +1,596 @@
+# Voron Design VORON2 300mm SKR 1.3 TMC2209 UART config
+
+# *** THINGS TO CHANGE/CHECK: ***
+# MCU paths                         	[mcu] section
+# Thermistor types                      [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
+# Z Endstop Switch location       		[homing_override] section
+# Z Endstop Switch  offset for Z0  		[stepper_z] section
+# Probe points                          [quad_gantry_level] section
+# Min & Max gantry corner postions      [quad_gantry_level] section
+# PID tune                              [extruder] and [heater_bed] sections
+# Fine tune E steps                     [extruder] section
+
+# ========================== Pin Definitions ========================
+# X_STEP_PIN         2.2
+# X_DIR_PIN          2.6
+# X_ENABLE_PIN       2.1
+# X_MIN_PIN          1.29
+# X_MAX_PIN          1.28
+# X_UART_RX          1.17
+# X_UART_TX          4.29
+
+# Y_STEP_PIN         0.19
+# Y_DIR_PIN          0.20
+# Y_ENABLE_PIN       2.8
+# Y_MIN_PIN          1.27
+# Y_MAX_PIN          1.26
+# Y_UART_RX          1.15
+# Y_UART_TX          1.16
+
+# Z_STEP_PIN         0.22
+# Z_DIR_PIN          2.11
+# Z_ENABLE_PIN       0.21
+# Z_MIN_PIN          1.25
+# Z_MAX_PIN          1.24
+# Z_UART_RX          1.10
+# Z_UART_TX          1.14
+
+# E0_STEP_PIN        2.13
+# E0_DIR_PIN         0.11
+# E0_ENABLE_PIN      2.12
+# E0_UART_RX         1.8
+# E0_UART_TX         1.9
+
+# E1_STEP_PIN        0.1
+# E1_DIR_PIN         0.0
+# E1_ENABLE_PIN      0.10
+# E1_UART_RX         1.1
+# E1_UART_TX         1.4
+
+# HE1                2.4    
+# HE0                2.7
+# BED                2.5
+# TH1 (H1 Temp)      0.25
+# TH0 (H0 Temp)      0.24
+# TB  (Bed Temp)     0.23
+# FAN                2.3
+# SERVO              2.0
+# ===================================================================
+
+[mcu]
+#	mcu for X/Y/E steppers main MCU
+#	[X in X] - B Motor
+#	[Y in Y] - A Motor
+#	[E in E0] - Extruder
+#	obtain definition by "ls -l /dev/serial/by-path/" then unplug to verify
+#--------------------------------------------------------------------
+serial: /dev/serial/by-path/platform-3f980000.usb-usb-0:1.1.2:1.0 
+#--------------------------------------------------------------------
+
+[mcu z]
+#	mcu for Z steppers
+#	[Z in X] - Front Left
+#	[Z1 in Y] - Rear Left
+#	[Z2 in Z] - Rear Right
+#	[Z3 in E0]- Front Right
+#	obtain definition by "ls -l /dev/serial/by-path/" then unplug to verify
+serial: /dev/serial/by-path/platform-3f980000.usb-usb-0:1.1.3:1.0
+
+[printer]
+kinematics: corexy
+max_velocity: 300  
+max_accel: 3000    #Max 4000
+max_z_velocity: 25 #Max 50
+max_z_accel: 350   #Max 800
+square_corner_velocity: 5.0  #Can experiment with 8.0, default 5.0
+
+#####################################################################
+# 	X/Y Stepper Settings
+#####################################################################
+
+[stepper_x]
+#connected to X on mcu_xye (B Motor)
+step_pin: P2.2
+dir_pin: !P2.6
+enable_pin: !P2.1
+step_distance: 0.0125
+endstop_pin: P1.28
+position_min: 0
+
+#--------------------------------------------------------------------
+#Uncomment below for 250mm build
+#position_endstop: 250
+#position_max: 250
+
+#Uncomment for 300mm build
+#position_endstop: 300
+#position_max: 300
+
+#Uncomment for 350mm build
+#position_endstop: 350
+#position_max: 350
+#--------------------------------------------------------------------
+
+homing_speed: 25   #Max 100
+homing_retract_dist: 5
+homing_positive_dir: true
+
+#Make sure to update below for your relevant driver (2208 or 2209)
+[tmcXXXX stepper_x]
+uart_pin: P1.17
+microsteps: 16
+interpolate: True
+run_current: 1.0
+hold_current: 0.9
+sense_resistor: 0.110
+stealthchop_threshold: 0
+
+[stepper_y]
+#connected to Y on mcu_xye (A Motor)
+step_pin: P0.19
+dir_pin: !P0.20
+enable_pin: !P2.8
+step_distance: 0.0125
+endstop_pin: P1.26
+position_min: 0
+#--------------------------------------------------------------------
+#Uncomment for 250mm build
+#position_endstop: 250
+#position_max: 250
+
+#Uncomment for 300mm build
+#position_endstop: 300
+#position_max: 300
+
+#Uncomment for 350mm build
+#position_endstop: 350
+#position_max: 350
+#--------------------------------------------------------------------
+
+homing_speed: 25  #Max 100
+homing_retract_dist: 5
+homing_positive_dir: true
+
+#Make sure to update below for your relevant driver (2208 or 2209)
+[tmcXXXX stepper_y]
+uart_pin: P1.15
+microsteps: 16
+interpolate: True
+run_current: 1.0
+hold_current: 0.9
+sense_resistor: 0.110
+stealthchop_threshold: 0
+ 
+#####################################################################
+# 	Z Stepper Settings
+#####################################################################
+
+#Z MCU - In X Position
+# Z0 Stepper - Front Left
+[stepper_z]
+step_pin: z:P2.2
+dir_pin: !z:P2.6
+enable_pin: !z:P2.1
+step_distance: 0.00250
+endstop_pin: z:P1.25
+#   Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
+#   (+) value = endstop above Z0, (-) value = endstop below
+#	Increasing position_endstop brings nozzle closer to the bed
+#   After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
+position_endstop: -0.5
+#--------------------------------------------------------------------
+#Uncomment for 250mm build
+#position_max: 240
+
+#Uncomment for 300mm build
+#position_max: 290
+
+#Uncomment for 350mm build
+#position_max: 340
+#--------------------------------------------------------------------
+position_min: -5
+homing_speed: 15.0
+second_homing_speed: 3.0
+homing_retract_dist: 3.0
+
+#Make sure to update below for your relevant driver (2208 or 2209)
+[tmcXXXX stepper_z]
+uart_pin: z:P1.17
+microsteps: 16
+interpolate: False
+run_current: 1.0
+hold_current: 0.8
+sense_resistor: 0.110
+stealthchop_threshold: 0
+
+#Z MCU - In Y Position
+# Z1 Stepper - Rear Left
+[stepper_z1]
+step_pin: z:P0.19
+dir_pin: z:P0.20
+enable_pin: !z:P2.8
+step_distance: 0.00250
+
+#Make sure to update below for your relevant driver (2208 or 2209)
+[tmcXXXX stepper_z1]
+uart_pin: z:P1.15
+microsteps: 16
+interpolate: False
+run_current: 1.0
+hold_current: 0.80
+sense_resistor: 0.110
+stealthchop_threshold: 0
+
+#Z MCU - In Z Position
+# Z2 Stepper - Rear Right
+[stepper_z2]
+step_pin: z:P0.22
+dir_pin: !z:P2.11
+enable_pin: !z:P0.21
+step_distance: 0.00250
+
+#Make sure to update below for your relevant driver (2208 or 2209)
+[tmcXXXX stepper_z2]
+uart_pin: z:P1.10
+microsteps: 16
+interpolate: False
+run_current: 1.0
+hold_current: 0.80
+sense_resistor: 0.110
+stealthchop_threshold: 0
+
+#Z MCU - In E0 Position
+# Z3 Stepper - Front Right
+[stepper_z3]
+step_pin: z:P2.13
+dir_pin: z:P0.11
+enable_pin: !z:P2.12
+step_distance: 0.00250
+
+#Make sure to update below for your relevant driver (2208 or 2209)
+[tmcXXXX stepper_z3]
+uart_pin: z:P1.8
+microsteps: 16
+interpolate: False
+run_current: 1.0
+hold_current: 0.80
+sense_resistor: 0.110
+stealthchop_threshold: 0
+
+
+#####################################################################
+# 	Extruder
+#####################################################################
+
+#E0 on MCU X/Y
+[extruder]
+step_pin: P2.13
+dir_pin: P0.11
+enable_pin: !P2.12
+# 16 microsteps Mobius 3 ~= 0.00180
+# Update value below when you perform extruder calibration
+# Higher value means less filament extruded
+# If you ask for 100mm of filament, but in reality it is 98mm:
+# step_distance = 98 / 100 * step_distance_old
+step_distance: 0.00180180
+nozzle_diameter: 0.400
+filament_diameter: 1.75
+heater_pin: P2.7
+#Validate the following thermistor type to make sure it is correct
+sensor_type: NTC 100K beta 3950
+sensor_pin: P0.24
+smooth_time: 3.0
+min_temp: 10
+max_temp: 270
+max_power: 1.0
+min_extrude_temp: 170
+control = pid
+pid_kp = 26.213
+pid_ki = 1.304
+pid_kd = 131.721
+# PA can be disabled by declaring a 0.0 value
+pressure_advance: 0.0
+# Time seconds to look ahead for PA moves default is 0.010 or 10ms
+pressure_advance_lookahead_time: 0.010
+
+#E0 on MCU X/Y
+#Make sure to update below for your relevant driver (2208 or 2209)
+[tmcXXXX extruder]
+uart_pin: P1.9
+microsteps: 16
+interpolate: false
+run_current: 1.0
+hold_current: 1.0
+sense_resistor: 0.110
+stealthchop_threshold: 0
+
+#####################################################################
+# 	Probe
+#####################################################################
+
+
+[probe]
+# Inductive Probe
+# This probe is not used for Z height, only Quad Gantry Leveling
+#   Z_MAX on mcu_z
+#   If your probe is NO instead of NC, add change pin to !z:P1.24
+pin: z:P1.24
+x_offset: 0
+y_offset: 25.0
+z_offset: 0
+speed: 10.0
+samples: 4
+samples_result: average
+sample_retract_dist: 3.0
+samples_tolerance: 0.006
+samples_tolerance_retries: 3
+
+
+#####################################################################
+# 	Fan Control
+#####################################################################
+
+[heater_fan hotend_fan]
+# Hotend Fan - XYE board, HE1 Connector
+pin: P2.4
+max_power: 1.0
+kick_start_time: 0.5
+heater: extruder
+heater_temp: 50.0
+#If you are experiencing back flow, you can reduce fan_speed
+#fan_speed: 1.0
+
+[fan]
+# Print Cooling Fan - XYE board, Fan Pin
+pin: P2.3
+kick_start_time: 0.5
+#depending on your fan, you may need to increase or reduce this value
+#if your fan will not start
+off_below: 0.13
+cycle_time: 0.001
+
+#[heater_fan exhaust_fan]
+# Exhaust fan - Z board, HE0 Connector
+#pin: z:P2.7
+#max_power: 1.0
+#shutdown_speed: 0.0
+#kick_start_time: 5.0
+#heater: heater_bed
+#heater_temp: 60
+#fan_speed: 1.0
+
+[heater_fan controller_fan]
+# Controller fan - Z board, HE1 Connector
+pin: z:P2.4
+kick_start_time: 0.500
+heater: heater_bed
+heater_temp: 45.0
+
+#####################################################################
+# 	Bed Heater
+#####################################################################
+
+[heater_bed]
+# SSR Pin - Z board, Fan Pin
+heater_pin: z:P2.3
+sensor_type: NTC 100K MGB18-104F39050L32
+sensor_pin: z:P0.23
+smooth_time: 3.0
+#Adjust Max Power so your heater doesn't warp your bed
+max_power: 0.6
+min_temp: 0
+max_temp: 120
+control: pid
+pid_kp: 58.437
+pid_ki: 2.347
+pid_kd: 363.769
+
+#####################################################################
+# 	Homing and Gantry Adjustment Routines
+#####################################################################
+
+[idle_timeout]
+timeout: 1800
+
+[homing_override]
+axes: z
+set_position_z: 0
+gcode:
+   G90
+   G0 Z5 F600
+   G28 X Y
+   #   XY Location of the Z Endstop Switch
+   #   Update X0 and Y0 to your values (such as X157, Y305) after going through
+   #   Z Endstop Pin Location Definition step.
+   G0 X0 Y0 F3600 
+   
+   G28 Z
+   G0 Z10 F1800
+   
+   #Uncomment for for your size printer:
+#--------------------------------------------------------------------
+   #250mm bed
+   G0 X125 Y125 Z30 F3600
+   
+   #300mm bed
+   #G0 X150 Y150 Z30 F3600
+   
+   #350mm bed
+   #G0 X175 Y175 Z30 F3600
+#--------------------------------------------------------------------
+
+   
+[quad_gantry_level]
+#   Use QUAD_GANTRY_LEVEL to level a gantry.
+#   Min & Max gantry corners - measure from nozzle at MIN (0,0) and 
+#   MAX (250, 250), (300,300), or (350,350) depending on your printer size
+#   to respective belt positions
+
+#--------------------------------------------------------------------
+# 	Gantry Corners for 250mm Build
+
+#gantry_corners:
+#	-60,-10
+#	310, 260 #Not sure about this
+#   Probe points
+#points:
+#	60,60
+#	60,200
+#	200,200
+#	200,60
+	
+# 	Gantry Corners for 300mm Build
+#gantry_corners:
+#	-60,-10
+#	360,310
+#   Probe points
+#points:
+#	60,60
+#	60,240
+#	240,240
+#	240,60
+
+# 	Gantry Corners for 350mm Build
+#gantry_corners:
+#	-60,-10
+#	410,360
+#   Probe points
+#points:
+#	60,60
+#	60,290
+#	290,290
+#	290,60
+
+#--------------------------------------------------------------------
+speed: 100
+horizontal_move_z: 10
+retries: 5
+retry_tolerance: 0.0075
+max_adjust: 10
+
+#####################################################################
+# 	Displays
+#####################################################################
+
+# Uncomment the display that you have. Display connects to Z MCU
+#--------------------------------------------------------------------
+
+#[display]
+# RepRapDiscount 128x64 Full Graphic Smart Controller
+#lcd_type: st7920
+#cs_pin: z:P1.19
+#sclk_pin: z:P1.20
+#sid_pin: z:P1.18
+#menu_timeout: 40
+#encoder_pins: ^z:P3.26, ^z:P3.25 
+#click_pin: ^!z:P0.28
+
+#--------------------------------------------------------------------
+
+#[display]
+# "mini12864 LCD Display
+#lcd_type: uc1701
+#cs_pin: z:P1.18
+#a0_pin: z:P1.19
+#encoder_pins: z:^P3.26,z:^P3.25
+#click_pin: z:^!P0.28
+#contrast: 63
+
+#[neopixel my_neopixel]
+#To control Neopixel RGB in mini12864 display
+#pin: z:P1.21
+#chain_count: 3
+#initial_RED: 0.1
+#initial_GREEN: 0.5
+#initial_BLUE: 0.0
+#color_order_GRB: False
+#--------------------------------------------------------------------
+
+
+#####################################################################
+# 	Macros
+#####################################################################
+
+[gcode_macro G32]
+gcode:
+    BED_MESH_CLEAR
+    G28
+    QUAD_GANTRY_LEVEL
+    G28
+    G0 X150 Y150 Z20 F6000
+   
+[gcode_macro PRINT_START]
+#   Use PRINT_START for the slicer starting script - please customise for your slicer of choice
+gcode:
+    G28                            ; home all axes
+    G1 Z20 F3000                   ; move nozzle away from bed
+   
+
+[gcode_macro PRINT_END]
+#   Use PRINT_END for the slicer ending script - please customise for your slicer of choice
+gcode:
+    M400                           ; wait for buffer to clear
+    G92 E0                         ; zero the extruder
+    G1 E-10.0 F3600                ; retract filament
+    G91                            ; relative positioning
+    G0 Z1.00 X20.0 Y20.0 F20000    ; move nozzle to remove stringing
+    TURN_OFF_HEATERS
+    M107                           ; turn off fan
+    G1 Z2 F3000                    ; move nozzle up 2mm
+    G90                            ; absolute positioning
+    G0  X125 Y250 F3600            ; park nozzle at rear
+    BED_MESH_CLEAR
+    
+
+#[gcode_macro LOAD_FILAMENT]
+#gcode:
+#   M83                            ; set extruder to relative
+#   G1 E750 F1800                  ; quickly load filament to down bowden
+#   G1 E30 F300                    ; slower extrusion for hotend path
+#   G1 E15 F150                    ; prime nozzle with filament
+#   M82                            ; set extruder to absolute
+    
+#[gcode_macro UNLOAD_FILAMENT]
+#gcode:
+#   M83                            ; set extruder to relative
+#   G1 E10 F300                    ; extrude a little to soften tip
+#   G1 E-780 F1800                 ; retract filament completely
+#   M82                            ; set extruder to absolute
+
+	
+# Sensor Types
+#   "EPCOS 100K B57560G104F"
+#   "ATC Semitec 104GT-2"
+#   "NTC 100K beta 3950"
+#   "Honeywell 100K 135-104LAG-J01"
+#   "NTC 100K MGB18-104F39050L32" (Keenovo Heater Pad)
+#   "AD595"
+#   "PT100 INA826"
+
+#	BED_MESH_CALIBRATE
+# Do not use unless absolutely necessary
+#[bed_mesh]
+#speed: 200
+#horizontal_move_z: 10
+#probe_count: 7,7
+#fade_start: 0.6
+#fade_end: 25.0
+#split_delta_z: .01
+#move_check_distance: 3
+#mesh_pps: 0,0
+#algorithm: bicubic
+#relative_reference_index: 24
+
+#For 250mm Size:
+#min_point: 40,10
+#max_point: 210,180
+
+#For 300mm Size:
+#min_point: 40,10
+#max_point: 260,230
+
+#For 350mm Size:
+#min_point: 40,10
+#max_point: 310,280
+
+

printer_mods/ArmyAg08/Logitech_C270_Mounts/README.md

@@ -2,13 +2,13 @@
 
 ### Overview
 
-These are parts to mount the [Logitech C270](https://www.amazon.com/Logitech-Widescreen-designed-Calling-Recording/dp/B004FHO5Y6) webcam to the front left side of the gantry or to the top center of the frame. There is a small USB wire recess on the gantry mount to wrap the cable around and run down the length of the gantry to the rest of the default cable management solutions. A USB extension will be required to run the cable properly. The camera is angled so it will clear side panels if enclosed as well. For larger builds, you may not be able to view the entire bed plate. You can use this [fisheye lens](https://www.amazon.com/gp/product/B0179JX8GC/) and this [adapter](https://www.thingiverse.com/thing:2561414) to increase the field of view.
+These are parts to mount the [Logitech C270](https://www.amazon.com/Logitech-Widescreen-designed-Calling-Recording/dp/B004FHO5Y6) or C310 webcam to the front left side of the gantry or to the top center of the frame. There is a small USB wire recess on the gantry mount to wrap the cable around and run down the length of the gantry to the rest of the default cable management solutions. A USB extension will be required to run the cable properly. The camera is angled so it will clear side panels if enclosed as well. For larger builds, you may not be able to view the entire bed plate. You can use this [fisheye lens](https://www.amazon.com/gp/product/B0179JX8GC/) and this [adapter](https://www.thingiverse.com/thing:2561414) to increase the field of view.
 
 To run the cable down the extrusion, you can either use this [cable cover](https://www.thingiverse.com/thing:1478147) or print the included 2020 cover. Printing the included model on its back makes it relatively weak but also a little easier to remove. It will break if you insert/remove more than 2-3 times. This model also lies flush with the Misumi extrusion profile unlike the Thingiverse model.
 
 ### Requirements
 
- * 1x C270 Webcam
+ * 1x C270/C310 Webcam
  * 1x M3x8 SHCS
  * 1x M3x16 SHCS
  * 1x M3 T-nut

printer_mods/Cerulean/Respooler/readme.md

@@ -0,0 +1 @@
+Attach to an esun spool to re-wind your tangled spools or put on a koil. Attached drill chuck to bolt head. 

printer_mods/Cerulean/readme.md

@@ -0,0 +1 @@
+Collection of Files from Cerulean

printer_mods/Danowar/AltZChain/readme.md

@@ -0,0 +1,10 @@
+# Alternative mounting for Z-Axis zipchain
+
+### Overview
+![Image](./AltZChain1.jpg)
+![Image](./AltZChain2.jpg)
+
+Mount Z-Axis zipchain under the rear gantry crossbar, instead of in front of it.  Cleaner look,
+and frees up some room back there.  Print 2 of each STL.  One anchor attaches to a standoff for
+the bottom.  The second standoff is use as a spacer to support the chain when gantry is in lower
+positions.  Additional zipchain links will also be needed.

printer_mods/Danowar/V2.2_Wrench/readme.md

@@ -0,0 +1,8 @@
+# Wrench for 2.2 Knobs and Panel Clips
+
+### Overview
+![Image](./2.2_Wrench.PNG)
+
+Two sided wrench for tightening knobs on the Voron 2.2 Z Drive and A/B Drives.
+Purpose of this wrench is to assist with gripping the knobs, NOT for over-torquing
+them.  Please follow guidelines in manual for proper tightness.

printer_mods/Gamsche/skirt_keystone/readme

@@ -0,0 +1 @@
+This part is 25mm wide and has a hole for a keystone jack for use with RJ45/USB/HDMI/etc jacks.  For whichever side of the center skirt panel you wish to place this part, drop down to the next lower size skirt end.  So if you are using a 350mm printer, use the 300mm skirt on that side.  Those skirts are 25mm shorter on each side and will allow the exact amount of room needed for this part.

printer_mods/Jasperkm/5mm_panel_mounting/readme.md

@@ -0,0 +1,6 @@
+
+
+### 5mm panel mounts Voron 2.2
+
+I edited the original files of panel mounting for a 5mm option (this is for 4mm panels + 1mm thickness of foam tape).
+

printer_mods/Jasperkm/Brush_holder/readme.md

@@ -0,0 +1,3 @@
+### Prerequisites
+
+This brush holder has slots for M3 nuts so you can tighten a random brush to the printed part with M3 bolts. Works well and is really solid. 

printer_mods/Jasperkm/Cable_management/readme.md

@@ -0,0 +1,6 @@
+
+### Cable management
+
+Some cable trunking STLs I designed for my electronics compartment as well as a 2020 slot cover that works well.
+
+![example](./IMG_20191109_215833.jpg?raw=true)

printer_mods/Jasperkm/Exhaust_fan_guard/readme.md

@@ -0,0 +1,3 @@
+### Exhaust fan guard
+
+This is a fan guard for the 120mm exhaust fan for some additional safety

printer_mods/Jasperkm/Fire_alarm_mount/readme.md

@@ -0,0 +1,3 @@
+### Fire alarm mount    
+
+This is just a simple part to mount a small fire alarm to the back panel of the printer with the panel holders. Hole spacing can be adjusted in cad to your own fire alarm

printer_mods/Jasperkm/LED_strip_holder/readme.md

@@ -0,0 +1,3 @@
+### LED strip holder  
+
+This led strip holder puts the LEDs at an angle towards the bottom and has some covers so is doesnt shine in your eyes when lookin at the printer

printer_mods/Jasperkm/Panel_key_wrench/readme.md

@@ -0,0 +1,3 @@
+### Panel key wrench
+
+This is a wrench to print for turning the panel keys. I noticed some of mine are quite tight so this helps a lot.

printer_mods/Jasperkm/Simple_tool_holder/readme.md

@@ -0,0 +1,3 @@
+### Simple tool holder
+
+This is a simple part using the V2.2 panel locks to mount 6x3 magnets which can hold some small metal tools. I use it for a small flashlight, tweezers and a razorblade for part removal 

printer_mods/Jasperkm/Skirt_mods/readme.md

@@ -0,0 +1,3 @@
+### Voron 2.2 skirt mods
+
+These are some mods for the skirts, one to add an electromechanical clock to the front skirt and one to add fans to the side skirts which blow directly over my stepper drivers.

printer_mods/PhilLeMint/Dual_LED_Light_Mount/ReadMe

@@ -0,0 +1,4 @@
+This is for a dual LED light bar setup.  Step files are included for your own modification.
+The LED cutouts may need to be modified depending on the dimensions of your light bar.
+Designed to be mounted at the front of the Voron so the lights don't blind you when looking inside :)
+Could be mounted anywhere though.

printer_mods/PhilLeMint/Indicator_Mount/ReadMe

@@ -0,0 +1 @@
+This mount is for any standard indicator as the one pictured.  Dial or Digital.  Mounts to the hot end fan using the two exisiting top screws

printer_mods/PhilLeMint/Panel_Mounting/ReadMe

@@ -0,0 +1,3 @@
+These brackets are 4.4mm deep.  They are designed to give a light squish on the foam without too much distortion.
+The foam is 3/32" thick from McMaster Carr
+STEP files are included for your own custom modification.

printer_mods/PhilLeMint/Velocity_Stack/ReadMe

@@ -0,0 +1,3 @@
+This is a fun velocity stack that serves no purpose what so ever except to look cool.  Has voron logo in center.  
+Requires 10 or 15mm Hot end fan so it won't hit the front panel
+Enjoy!

printer_mods/PhilLeMint/c920_Mount/ReadMe

@@ -0,0 +1,3 @@
+c920 Mount.  Supports are needed at the boss.  If mounted at the front of a 350 voron the entire build surface is in view.
+Instructions for c920 dissasembly can be found here:  https://www.ifixit.com/Guide/Logitech+C920+Webcam+Disassembly/115077
+Some massaging of the D shaped bushing hole may be needed.

printer_mods/README.md

@@ -26,14 +26,18 @@ If your mod is lacking a column in the compatibility matrix, feel free to submit
 | 3D_Black   | [Fan Covers](./3D_Black) | Different fan covers for 40mm fans | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: |
 |Andreq | [Mobius Shaft Jig](./andreq/voron2)|Tool used for grinding flats on a shaft at specific places |:heavy_check_mark: |:heavy_check_mark: |:heavy_check_mark: |
 |Armstr0ng |[Led extrusions mount](./Armstr0ng) | A mount for aluminium LED extrusions with hidden fasteners  | :grey_question:|:heavy_check_mark: | :heavy_check_mark:|
-| ArmyAg08|[Logitech C270 Mounts](./ArmyAg08/Logitech_C270_Mounts) |Different C270 camera mounts, attached to the extrusions |:heavy_check_mark: |:heavy_check_mark: |:heavy_check_mark: |
+| ArmyAg08|[Logitech Camera Mounts](./ArmyAg08/Logitech_C270_Mounts) |Different Logitech camera mounts, attached to the extrusions. Fits C270 and C310 |:heavy_check_mark: |:heavy_check_mark: |:heavy_check_mark: |
 | | [Corner Panel Clip](./ArmyAg08/Panels)|Corner panel clip that fit 3mm or 1/8" panels with foam tape | :x:|:heavy_check_mark: | :heavy_check_mark:|
+| blamm   | [Blind Joint Drilling Jigs](./blamm/jigs) | Jigs to drill your blind joints in the right spot | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: |
+| Cerulean   | [Respooler](./Cerulean/Respooler) | Respool tangled spools or bad koils | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: |
 |Danowar |[Dual Mobius Mount](./Danowar/Dual_Mobuis_Mount) | Mounts two Mobius Extruders to the back of the printer| :heavy_check_mark:| :heavy_check_mark:|:heavy_check_mark: |
 | |[F6 Board Mount](./Danowar/F6_Board_Mount) | Mounts for FYSETCS F6 controller boards|:heavy_check_mark: | :heavy_check_mark:| :heavy_check_mark:|
 | |[Humidity Sensor Bracket](./Danowar/Humidity_Sensor_Bracket) |Mount for Humidity/Temperature sensor |:heavy_check_mark: |:heavy_check_mark: | :heavy_check_mark:|
-| | [Load Cell Spool Holder](./Danowar/Load_Cell_Spool_Holder)| Spool holder with built in weight scale|:x: |:heavy_check_mark: |:heavy_check_mark: |
-| | [TL 2-to-1 Mosquito Toolhead Adapter](./Danowar/TL_2-to-1_Mosquito_Toolhead_Adapter)| Mounts the Triangle Labs 2-to-1 adapter directly to the mosquito toolhead|:heavy_check_mark: |:heavy_check_mark: |:heavy_check_mark: |
-| | [Tablet mount](./Danowar/Tablet_Mount)|Detachable mount for tablet using magnets |:heavy_check_mark:  |:heavy_check_mark:  | :heavy_check_mark: |
+| |[Load Cell Spool Holder](./Danowar/Load_Cell_Spool_Holder)| Spool holder with built in weight scale|:x: |:heavy_check_mark: |:heavy_check_mark: |
+| |[TL 2-to-1 Mosquito Toolhead Adapter](./Danowar/TL_2-to-1_Mosquito_Toolhead_Adapter)| Mounts the Triangle Labs 2-to-1 adapter directly to the mosquito toolhead|:heavy_check_mark: |:heavy_check_mark: |:heavy_check_mark: |
+| |[Tablet mount](./Danowar/Tablet_Mount)|Detachable mount for tablet using magnets |:heavy_check_mark:  |:heavy_check_mark:  | :heavy_check_mark: |
+| |[V2.2 Wrench](./Danowar/V2.2_Wrench)|3 sided wrench for 2.2 bearing caps and panel clips |:x:  |:x:  | :heavy_check_mark: |
+| |[Alternative Z Chain](./Danowar/AltZChain)|Alternative mounting for Z-Axis zipchain|:x:  |:heavy_check_mark:  | :heavy_check_mark: |
 | daveidmx| [30mm Fan Adapter](./daveidmx/VORON2)|30mm Fan Adapter | :grey_question:| :grey_question:|:grey_question: |
 |Dunar |[Panel Rest](./Dunar/Panel_Rest) | External panel holder | :heavy_check_mark: |:heavy_check_mark:  |:heavy_check_mark:  |
 |etherwalker |[Pi Zero Camera Mount](./etherwalker/Pi_Zero_Camera_Mount) | Pi Zero Camera Mount| :grey_question:| :grey_question:|:grey_question: |
@@ -44,11 +48,21 @@ If your mod is lacking a column in the compatibility matrix, feel free to submit
 |FHeilmann |[Voron 2.1 5mm Parts](./FHeilmann/VORON2.1_5mm_parts) |Parts modified for extrusions with 5mm gap. |:x: |:heavy_check_mark: | :x:|
 | Fulg| [PanelDue5 LCD Mount](./Fulg/VORON2/PanelDue5)|Mount for the PanelDue5 LCD display |:heavy_check_mark: | :heavy_check_mark:|:heavy_check_mark: |
 |GSL12 |[WAGO 221 Mounts](./GSL12/wago_221_mount)   | Wago 221 mounts for the electronics bay |:heavy_check_mark: |:heavy_check_mark: | :heavy_check_mark:|
+|Gamsche | [Keystone Skirt Panel](./Gamsche/skirt_keystone)| 25mm skirt panel with integrated keystone jack.  Use with 50mm smaller adjacent skirts for proper fit. |:grey_question: |:grey_question: |:heavy_check_mark:|
 |Glowtape | [MKS GenL 1.0 Mounting Bracket](./Glowtape)| MKS GenL 1.0 Mounting Bracket|:heavy_check_mark: |:heavy_check_mark: |:heavy_check_mark:|
 |GustavTheMighty | [4.3 PanelDue Case](./GustavtheMighty/4.3-Paneldue_Case)|Case/mount for the 4.3 PanelDue LCD Display  |:heavy_check_mark:  | :heavy_check_mark: |:heavy_check_mark:  |
 |Iakabos | [Mini12864 Display Mount](./Iakabos/Mini12864_display_mount)|Case and mounting arms for a Fysetc Mini12864 display |:grey_question: |:heavy_check_mark: |:heavy_check_mark: |
 | Hackdoggo| [BMGobius](./hackdoggo/v2/bmgobius)|Modification to MZBot's Mobius Extruder to use dual drive Bondtech drivegears |:heavy_check_mark:  | :heavy_check_mark: | :heavy_check_mark: |
 |hiemmer | [Tool Holders](./hiemmer/Tool_Holders)| Tool holder for calipers, screwdriver etc| :grey_question:| :grey_question:|:grey_question: |
+| Jasperkm | [5mm panel mounting](./Jasperkm/5mm_panel_mounting)| Edited panel clips for 4mm panel + 1mm foam tape| :x: | :heavy_check_mark: | :heavy_check_mark: |
+| | [Brush holder](./Jasperkm/Brush_holder)| Brush holder next to printbed | :x: | :heavy_check_mark: | :heavy_check_mark: |
+| | [Cable management](./Jasperkm/Cable_management)| Cable trunking and 2020 slot cover | :x: | :heavy_check_mark: | :heavy_check_mark: |
+| | [Exhaust fan guard](./Jasperkm/Exhaust_fan_guard)| VORON styled fan guard for exhaust fan 120mm | :x: | :heavy_check_mark: | :heavy_check_mark: |
+| | [Fire alarm mount](./Jasperkm/Fire_alarm_mount)| Mount for a small fire alarm on the back of the printer | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: |
+| | [LED strip holder](./Jasperkm/LED_strip_holder)| Mount for led strips at an angle at the top of the printer | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: |
+| | [Panel key wrench](./Jasperkm/Panel_key_wrench)| Wrench for panel keys for ease of turning | :x: | :heavy_check_mark: | :heavy_check_mark: |
+| | [Simple tool holder](./Jasperkm/Simple_tool_holder)| Holder for 3 small tools using magnets | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: |
+| | [Skirt mods](./Jasperkm/Skirt_mods)| Some mods the skirts for fans and a clock | :x: | :heavy_check_mark: | :heavy_check_mark: |
 |Jass_on |[Tempered glass clips/handle](./Jass_on/Voron_2.1.1_Tempered_Glass) |Panel clips and handles for using tempered glass side panels | :x: | :heavy_check_mark: | :grey_question:|
 | | [Rear panel clips](./Jass_on) | Rear Panel Clips| :x: | :heavy_check_mark: | :grey_question:|
 | | [SKR 1.3 Cooling bracket](./Jass_on)|SKR 1.3 mount with built in 40mm fan mount |:heavy_check_mark:  | :heavy_check_mark: | :heavy_check_mark: |
@@ -65,8 +79,14 @@ If your mod is lacking a column in the compatibility matrix, feel free to submit
 |Koios |[Front Panel Locks](./Koios/6mm_Glass) |Front panel locks for 6mm tempered glass panels | :x: | :heavy_check_mark: | :grey_question:|
 | |[Logitech C920 Mount](./Koios) |Mount for C920 secured to the top front extrusion |:grey_question: |:heavy_check_mark: | :heavy_check_mark:|
 | |[LED Mounts](./Koios) |Different mounts for LED light bars |:grey_question: |:heavy_check_mark: | :heavy_check_mark:|
+|manfre |[Openbuild chain ends](./manfre/cable_chains) |Cable chain ends to use off the shelf chains with Voron parts |:x: |:heavy_check_mark: |:heavy_check_mark: |
 |nemgrea |[Magnetic Split Front Door](./nemgrea/magnetic_split_front_door) |Hinges, handles and magnet mounts for creating a split front door panel |:x: |:heavy_check_mark: |:grey_question: |
 |OrkusMG | [Waveshare 5 Inch LCD Cover](./OrkusMG/Waveshare5inchHDMILCDscreenCover)|Display Cover for the Waveshare 5 inch HDMI LCD screen |:heavy_check_mark: |:heavy_check_mark: | :heavy_check_mark:|
+|PhilLeMint | [c920 Mount](./PhilLeMint/c920_Mount/) | c920 Camera Mount | :grey_question: | :heavy_check_mark: | :heavy_check_mark: |
+| |[Panel Mounting](./PhilLeMint/Panel_Mounting/) | Panel Clips for 3/32" Foam Tape |:grey_question: | :heavy_check_mark: |:heavy_check_mark: |
+| |[Dual LED Light Mount](./PhilLeMint/Dual_LED_Light_Mount/) | Mounts for Dual LED Bar |:grey_question: | :heavy_check_mark: |:heavy_check_mark: |
+| |[Velocity Stack](./PhilLeMint/Velocity_Stack/) | Velocity Stack Fan Cover |:grey_question: | :heavy_check_mark: |:heavy_check_mark: |
+| |[Indicator Mount](./PhilLeMint/Indicator_Mount/) | Mount for Indicator |:grey_question: | :heavy_check_mark: |:heavy_check_mark: |
 |pnokel |[Cable Zipper](./pnokel) |Small mount to secure wires with zip ties |:heavy_check_mark: | :heavy_check_mark:|:heavy_check_mark: |
 | |[Coroplast holders](./pnokel) | Different coroplast holders for added support |:x:| :heavy_check_mark:|:grey_question: |
 | |[Toothed Idler](./pnokel) |14.5mm toothed idler | :x: | :x: |:x:|
@@ -88,11 +108,13 @@ If your mod is lacking a column in the compatibility matrix, feel free to submit
 | |[LED Mount](./synfinatic/LED-Mount) |Mount for LED lightbars |:grey_question: |:heavy_check_mark: |:heavy_check_mark: |
 | | [PS Extra Bracket](./synfinatic/PS-Extra-Bracket)|Extra bracket to keep the power supply in place |:grey_question: |:grey_question: |:grey_question: |
 | |[RJ45 Mount](./synfinatic/RJ45-Mount) |Mount for an ethernet coupler to extend / move the ethernet plug somewhere more convenient |:grey_question: |:grey_question: |:grey_question: |
+|Trippinonaduck |[Switch Holder](./Trippinonaduck/SwitchHolder) | Holder for Anit-Vandal Switches mounted in skirt holes  | :x:|:heavy_check_mark: | :heavy_check_mark:|
+| |[LRS-75-5](./Trippinonaduck/LRS_75_5) | Mount for LRS-75-5 Power Supply  | :heavy_check_mark:|:heavy_check_mark: | :heavy_check_mark:|
 |warriorofwire | [Openbuilds Drag Chain](./warriorofwire/openbuilds_drag_chain)|Collection of models for using an off-the-shelf, cheap, snap opening drag chain for gantry wiring and protecting wires down to the deck |:x: | :heavy_check_mark: | :x: |
 | | [Direct Drive BMG-m mount](./warriorofwire/bmg_direct_drive)| Open toolhead mounting plans for Bondtech BMG-m and Mosquito direct drive combo|:grey_question: |:heavy_check_mark:|:grey_question: |
 | wile.e.coyote| [Coroplast Support](./wile.e.coyote)|Support for the coroplast to prevent sagging | :x: |:heavy_check_mark: |:grey_question: |
 | |[Dual Buck Bracket](./wile.e.coyote)   |Mounting bracket for 2 buck converters | :heavy_check_mark: |:heavy_check_mark: |:heavy_check_mark: |
 | |[Nozzle Scrubber Mount](./wile.e.coyote) | Mount for brass brush. Used for cleaning nozzle before printing |:x: | :heavy_check_mark: |:heavy_check_mark: |
-| | [Wago Mounts](./wile.e.coyote)  | Different mounts for Wago connectors | :heavy_check_mark: |:heavy_check_mark: |:heavy_check_mark: |
+| | [Wago Mounts](./wile.e.coyote)  | Different mounts for Wago connectors | :heavy_check_mark: |:heavy_check_mark: |:heavy_check_mark: | 
 
 ---

printer_mods/Trippinonaduck/LRS_75_5/Readme.md

@@ -0,0 +1 @@
+This is a Mounting bracket for holding a LRS-75-5 to 2020 extrusion.

printer_mods/Trippinonaduck/SwitchHolder/Readme.md

@@ -0,0 +1,3 @@
+![Switch Image](Switchpreview.jpg?raw=true "Switch Image")
+
+This is a switch holder intended for holding 19mm anti vandal momentary/latching pushbutton switches in the open hexagons in the skirts of Voron 2.1/2.2

printer_mods/blamm/jigs/README.md

@@ -0,0 +1,6 @@
+Small jig to drill the blind holes in your 2020 extrusions.
+
+Secure it with a bolt on the top, M5 for most extrusions, M6 for Type-B (Bosch) extrusions.
+Most extrusions need the 6mm files, unless you also print the 5mm files for your Voron, then pick that one.
+
+![Blind Joint Jig](blind_hole_jig.png)