Updated eddies SKR Guide/Config (#31)
This commit is contained in:
Joshua Longenecker
Florian Heilmann
parent
7880fec167
commit
c5103a6c8b
Binary file not shown.
|
|
@ -1,87 +1,89 @@
|
||||||
# Voron Design VORON2 300mm SKR 1.3 TMC2209 UART config
|
## Voron Design VORON2 300mm SKR 1.3 TMC2209 UART config
|
||||||
|
|
||||||
# *** THINGS TO CHANGE/CHECK: ***
|
## *** THINGS TO CHANGE/CHECK: ***
|
||||||
# MCU paths [mcu] section
|
## MCU paths [mcu] section
|
||||||
# Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
|
## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
|
||||||
# Z Endstop Switch location [homing_override] section
|
## Z Endstop Switch location [homing_override] section
|
||||||
# Z Endstop Switch offset for Z0 [stepper_z] section
|
## Z Endstop Switch offset for Z0 [stepper_z] section
|
||||||
# Probe points [quad_gantry_level] section
|
## Probe points [quad_gantry_level] section
|
||||||
# Min & Max gantry corner postions [quad_gantry_level] section
|
## Min & Max gantry corner postions [quad_gantry_level] section
|
||||||
# PID tune [extruder] and [heater_bed] sections
|
## PID tune [extruder] and [heater_bed] sections
|
||||||
# Fine tune E steps [extruder] section
|
## Fine tune E steps [extruder] section
|
||||||
|
|
||||||
# ========================== Pin Definitions ========================
|
##========================== Pin Definitions ========================
|
||||||
# X_STEP_PIN 2.2
|
## X_STEP_PIN 2.2
|
||||||
# X_DIR_PIN 2.6
|
## X_DIR_PIN 2.6
|
||||||
# X_ENABLE_PIN 2.1
|
## X_ENABLE_PIN 2.1
|
||||||
# X_MIN_PIN 1.29
|
## X_MIN_PIN 1.29
|
||||||
# X_MAX_PIN 1.28
|
## X_MAX_PIN 1.28
|
||||||
# X_UART_RX 1.17
|
## X_UART_RX 1.17
|
||||||
# X_UART_TX 4.29
|
## X_UART_TX 4.29
|
||||||
|
|
||||||
# Y_STEP_PIN 0.19
|
## Y_STEP_PIN 0.19
|
||||||
# Y_DIR_PIN 0.20
|
## Y_DIR_PIN 0.20
|
||||||
# Y_ENABLE_PIN 2.8
|
## Y_ENABLE_PIN 2.8
|
||||||
# Y_MIN_PIN 1.27
|
## Y_MIN_PIN 1.27
|
||||||
# Y_MAX_PIN 1.26
|
## Y_MAX_PIN 1.26
|
||||||
# Y_UART_RX 1.15
|
## Y_UART_RX 1.15
|
||||||
# Y_UART_TX 1.16
|
## Y_UART_TX 1.16
|
||||||
|
|
||||||
# Z_STEP_PIN 0.22
|
## Z_STEP_PIN 0.22
|
||||||
# Z_DIR_PIN 2.11
|
## Z_DIR_PIN 2.11
|
||||||
# Z_ENABLE_PIN 0.21
|
## Z_ENABLE_PIN 0.21
|
||||||
# Z_MIN_PIN 1.25
|
## Z_MIN_PIN 1.25
|
||||||
# Z_MAX_PIN 1.24
|
## Z_MAX_PIN 1.24
|
||||||
# Z_UART_RX 1.10
|
## Z_UART_RX 1.10
|
||||||
# Z_UART_TX 1.14
|
## Z_UART_TX 1.14
|
||||||
|
|
||||||
# E0_STEP_PIN 2.13
|
## E0_STEP_PIN 2.13
|
||||||
# E0_DIR_PIN 0.11
|
## E0_DIR_PIN 0.11
|
||||||
# E0_ENABLE_PIN 2.12
|
## E0_ENABLE_PIN 2.12
|
||||||
# E0_UART_RX 1.8
|
## E0_UART_RX 1.8
|
||||||
# E0_UART_TX 1.9
|
## E0_UART_TX 1.9
|
||||||
|
|
||||||
# E1_STEP_PIN 0.1
|
## E1_STEP_PIN 0.1
|
||||||
# E1_DIR_PIN 0.0
|
## E1_DIR_PIN 0.0
|
||||||
# E1_ENABLE_PIN 0.10
|
## E1_ENABLE_PIN 0.10
|
||||||
# E1_UART_RX 1.1
|
## E1_UART_RX 1.1
|
||||||
# E1_UART_TX 1.4
|
## E1_UART_TX 1.4
|
||||||
|
|
||||||
# HE1 2.4
|
## HE1 2.4
|
||||||
# HE0 2.7
|
## HE0 2.7
|
||||||
# BED 2.5
|
## BED 2.5
|
||||||
# TH1 (H1 Temp) 0.25
|
## TH1 (H1 Temp) 0.25
|
||||||
# TH0 (H0 Temp) 0.24
|
## TH0 (H0 Temp) 0.24
|
||||||
# TB (Bed Temp) 0.23
|
## TB (Bed Temp) 0.23
|
||||||
# FAN 2.3
|
## FAN 2.3
|
||||||
# SERVO 2.0
|
## SERVO 2.0
|
||||||
# ===================================================================
|
##===================================================================
|
||||||
|
|
||||||
[mcu]
|
[mcu]
|
||||||
# mcu for X/Y/E steppers main MCU
|
## MCU for X/Y/E steppers main MCU
|
||||||
# [X in X] - B Motor
|
## [X in X] - B Motor
|
||||||
# [Y in Y] - A Motor
|
## [Y in Y] - A Motor
|
||||||
# [E in E0] - Extruder
|
## [E in E0] - Extruder
|
||||||
# obtain definition by "ls -l /dev/serial/by-path/" then unplug to verify
|
## Obtain definition by "ls -l /dev/serial/by-path/" then unplug to verify
|
||||||
#--------------------------------------------------------------------
|
##--------------------------------------------------------------------
|
||||||
serial: /dev/serial/by-path/platform-3f980000.usb-usb-0:1.1.2:1.0
|
serial: /dev/serial/by-path/platform-3f980000.usb-usb-0:1.1.2:1.0
|
||||||
#--------------------------------------------------------------------
|
##--------------------------------------------------------------------
|
||||||
|
|
||||||
[mcu z]
|
[mcu z]
|
||||||
# mcu for Z steppers
|
## MCU for Z steppers
|
||||||
# [Z in X] - Front Left
|
## [Z in X] - Front Left
|
||||||
# [Z1 in Y] - Rear Left
|
## [Z1 in Y] - Rear Left
|
||||||
# [Z2 in Z] - Rear Right
|
## [Z2 in Z] - Rear Right
|
||||||
# [Z3 in E0]- Front Right
|
## [Z3 in E0]- Front Right
|
||||||
# obtain definition by "ls -l /dev/serial/by-path/" then unplug to verify
|
## Obtain definition by "ls -l /dev/serial/by-path/" then unplug to verify
|
||||||
|
##--------------------------------------------------------------------
|
||||||
serial: /dev/serial/by-path/platform-3f980000.usb-usb-0:1.1.3:1.0
|
serial: /dev/serial/by-path/platform-3f980000.usb-usb-0:1.1.3:1.0
|
||||||
|
##--------------------------------------------------------------------
|
||||||
|
|
||||||
[printer]
|
[printer]
|
||||||
kinematics: corexy
|
kinematics: corexy
|
||||||
max_velocity: 300
|
max_velocity: 300
|
||||||
max_accel: 3000 #Max 4000
|
max_accel: 3000 #Max 4000
|
||||||
max_z_velocity: 25 #Max 50
|
max_z_velocity: 15 #Max 15 for 12V TMC Drivers
|
||||||
max_z_accel: 350 #Max 800
|
max_z_accel: 350 #Max ?
|
||||||
square_corner_velocity: 5.0 #Can experiment with 8.0, default 5.0
|
square_corner_velocity: 5.0 #Can experiment with 8.0, default 5.0
|
||||||
|
|
||||||
#####################################################################
|
#####################################################################
|
||||||
|
|
@ -89,33 +91,33 @@ square_corner_velocity: 5.0 #Can experiment with 8.0, default 5.0
|
||||||
#####################################################################
|
#####################################################################
|
||||||
|
|
||||||
[stepper_x]
|
[stepper_x]
|
||||||
#connected to X on mcu_xye (B Motor)
|
## Connected to X on mcu_xye (B Motor)
|
||||||
step_pin: P2.2
|
step_pin: P2.2
|
||||||
dir_pin: !P2.6
|
dir_pin: P2.6
|
||||||
enable_pin: !P2.1
|
enable_pin: !P2.1
|
||||||
step_distance: 0.0125
|
step_distance: 0.0125
|
||||||
endstop_pin: P1.28
|
endstop_pin: P1.28
|
||||||
position_min: 0
|
position_min: 0
|
||||||
|
##--------------------------------------------------------------------
|
||||||
|
|
||||||
#--------------------------------------------------------------------
|
## Uncomment below for 250mm build
|
||||||
#Uncomment below for 250mm build
|
|
||||||
#position_endstop: 250
|
#position_endstop: 250
|
||||||
#position_max: 250
|
#position_max: 250
|
||||||
|
|
||||||
#Uncomment for 300mm build
|
## Uncomment for 300mm build
|
||||||
#position_endstop: 300
|
#position_endstop: 300
|
||||||
#position_max: 300
|
#position_max: 300
|
||||||
|
|
||||||
#Uncomment for 350mm build
|
## Uncomment for 350mm build
|
||||||
#position_endstop: 350
|
#position_endstop: 350
|
||||||
#position_max: 350
|
#position_max: 350
|
||||||
#--------------------------------------------------------------------
|
|
||||||
|
|
||||||
|
##--------------------------------------------------------------------
|
||||||
homing_speed: 25 #Max 100
|
homing_speed: 25 #Max 100
|
||||||
homing_retract_dist: 5
|
homing_retract_dist: 5
|
||||||
homing_positive_dir: true
|
homing_positive_dir: true
|
||||||
|
|
||||||
#Make sure to update below for your relevant driver (2208 or 2209)
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||||
[tmcXXXX stepper_x]
|
[tmcXXXX stepper_x]
|
||||||
uart_pin: P1.17
|
uart_pin: P1.17
|
||||||
microsteps: 16
|
microsteps: 16
|
||||||
|
|
@ -126,32 +128,33 @@ sense_resistor: 0.110
|
||||||
stealthchop_threshold: 0
|
stealthchop_threshold: 0
|
||||||
|
|
||||||
[stepper_y]
|
[stepper_y]
|
||||||
#connected to Y on mcu_xye (A Motor)
|
## Connected to Y on mcu_xye (A Motor)
|
||||||
step_pin: P0.19
|
step_pin: P0.19
|
||||||
dir_pin: !P0.20
|
dir_pin: P0.20
|
||||||
enable_pin: !P2.8
|
enable_pin: !P2.8
|
||||||
step_distance: 0.0125
|
step_distance: 0.0125
|
||||||
endstop_pin: P1.26
|
endstop_pin: P1.26
|
||||||
position_min: 0
|
position_min: 0
|
||||||
#--------------------------------------------------------------------
|
##--------------------------------------------------------------------
|
||||||
#Uncomment for 250mm build
|
|
||||||
|
## Uncomment for 250mm build
|
||||||
#position_endstop: 250
|
#position_endstop: 250
|
||||||
#position_max: 250
|
#position_max: 250
|
||||||
|
|
||||||
#Uncomment for 300mm build
|
## Uncomment for 300mm build
|
||||||
#position_endstop: 300
|
#position_endstop: 300
|
||||||
#position_max: 300
|
#position_max: 300
|
||||||
|
|
||||||
#Uncomment for 350mm build
|
## Uncomment for 350mm build
|
||||||
#position_endstop: 350
|
#position_endstop: 350
|
||||||
#position_max: 350
|
#position_max: 350
|
||||||
#--------------------------------------------------------------------
|
|
||||||
|
|
||||||
|
##--------------------------------------------------------------------
|
||||||
homing_speed: 25 #Max 100
|
homing_speed: 25 #Max 100
|
||||||
homing_retract_dist: 5
|
homing_retract_dist: 5
|
||||||
homing_positive_dir: true
|
homing_positive_dir: true
|
||||||
|
|
||||||
#Make sure to update below for your relevant driver (2208 or 2209)
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||||
[tmcXXXX stepper_y]
|
[tmcXXXX stepper_y]
|
||||||
uart_pin: P1.15
|
uart_pin: P1.15
|
||||||
microsteps: 16
|
microsteps: 16
|
||||||
|
|
@ -165,35 +168,37 @@ stealthchop_threshold: 0
|
||||||
# Z Stepper Settings
|
# Z Stepper Settings
|
||||||
#####################################################################
|
#####################################################################
|
||||||
|
|
||||||
#Z MCU - In X Position
|
## Z MCU - In X Position
|
||||||
# Z0 Stepper - Front Left
|
## Z0 Stepper - Front Left
|
||||||
[stepper_z]
|
[stepper_z]
|
||||||
step_pin: z:P2.2
|
step_pin: z:P2.2
|
||||||
dir_pin: !z:P2.6
|
dir_pin: !z:P2.6
|
||||||
enable_pin: !z:P2.1
|
enable_pin: !z:P2.1
|
||||||
step_distance: 0.00250
|
step_distance: 0.00250
|
||||||
endstop_pin: z:P1.25
|
endstop_pin: z:P1.25
|
||||||
# Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
||||||
# (+) value = endstop above Z0, (-) value = endstop below
|
## (+) value = endstop above Z0, (-) value = endstop below
|
||||||
# Increasing position_endstop brings nozzle closer to the bed
|
## Increasing position_endstop brings nozzle closer to the bed
|
||||||
# After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
||||||
position_endstop: -0.5
|
position_endstop: -0.5
|
||||||
#--------------------------------------------------------------------
|
##--------------------------------------------------------------------
|
||||||
#Uncomment for 250mm build
|
|
||||||
|
## Uncomment below for 250mm build
|
||||||
#position_max: 240
|
#position_max: 240
|
||||||
|
|
||||||
#Uncomment for 300mm build
|
## Uncomment below for 300mm build
|
||||||
#position_max: 290
|
#position_max: 290
|
||||||
|
|
||||||
#Uncomment for 350mm build
|
## Uncomment below for 350mm build
|
||||||
#position_max: 340
|
#position_max: 340
|
||||||
#--------------------------------------------------------------------
|
|
||||||
|
##--------------------------------------------------------------------
|
||||||
position_min: -5
|
position_min: -5
|
||||||
homing_speed: 15.0
|
homing_speed: 15.0
|
||||||
second_homing_speed: 3.0
|
second_homing_speed: 3.0
|
||||||
homing_retract_dist: 3.0
|
homing_retract_dist: 3.0
|
||||||
|
|
||||||
#Make sure to update below for your relevant driver (2208 or 2209)
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||||
[tmcXXXX stepper_z]
|
[tmcXXXX stepper_z]
|
||||||
uart_pin: z:P1.17
|
uart_pin: z:P1.17
|
||||||
microsteps: 16
|
microsteps: 16
|
||||||
|
|
@ -203,15 +208,15 @@ hold_current: 0.8
|
||||||
sense_resistor: 0.110
|
sense_resistor: 0.110
|
||||||
stealthchop_threshold: 0
|
stealthchop_threshold: 0
|
||||||
|
|
||||||
#Z MCU - In Y Position
|
## Z MCU - In Y Position
|
||||||
# Z1 Stepper - Rear Left
|
## Z1 Stepper - Rear Left
|
||||||
[stepper_z1]
|
[stepper_z1]
|
||||||
step_pin: z:P0.19
|
step_pin: z:P0.19
|
||||||
dir_pin: z:P0.20
|
dir_pin: z:P0.20
|
||||||
enable_pin: !z:P2.8
|
enable_pin: !z:P2.8
|
||||||
step_distance: 0.00250
|
step_distance: 0.00250
|
||||||
|
|
||||||
#Make sure to update below for your relevant driver (2208 or 2209)
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||||
[tmcXXXX stepper_z1]
|
[tmcXXXX stepper_z1]
|
||||||
uart_pin: z:P1.15
|
uart_pin: z:P1.15
|
||||||
microsteps: 16
|
microsteps: 16
|
||||||
|
|
@ -221,15 +226,15 @@ hold_current: 0.80
|
||||||
sense_resistor: 0.110
|
sense_resistor: 0.110
|
||||||
stealthchop_threshold: 0
|
stealthchop_threshold: 0
|
||||||
|
|
||||||
#Z MCU - In Z Position
|
## Z MCU - In Z Position
|
||||||
# Z2 Stepper - Rear Right
|
## Z2 Stepper - Rear Right
|
||||||
[stepper_z2]
|
[stepper_z2]
|
||||||
step_pin: z:P0.22
|
step_pin: z:P0.22
|
||||||
dir_pin: !z:P2.11
|
dir_pin: !z:P2.11
|
||||||
enable_pin: !z:P0.21
|
enable_pin: !z:P0.21
|
||||||
step_distance: 0.00250
|
step_distance: 0.00250
|
||||||
|
|
||||||
#Make sure to update below for your relevant driver (2208 or 2209)
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||||
[tmcXXXX stepper_z2]
|
[tmcXXXX stepper_z2]
|
||||||
uart_pin: z:P1.10
|
uart_pin: z:P1.10
|
||||||
microsteps: 16
|
microsteps: 16
|
||||||
|
|
@ -239,15 +244,15 @@ hold_current: 0.80
|
||||||
sense_resistor: 0.110
|
sense_resistor: 0.110
|
||||||
stealthchop_threshold: 0
|
stealthchop_threshold: 0
|
||||||
|
|
||||||
#Z MCU - In E0 Position
|
## Z MCU - In E0 Position
|
||||||
# Z3 Stepper - Front Right
|
## Z3 Stepper - Front Right
|
||||||
[stepper_z3]
|
[stepper_z3]
|
||||||
step_pin: z:P2.13
|
step_pin: z:P2.13
|
||||||
dir_pin: z:P0.11
|
dir_pin: z:P0.11
|
||||||
enable_pin: !z:P2.12
|
enable_pin: !z:P2.12
|
||||||
step_distance: 0.00250
|
step_distance: 0.00250
|
||||||
|
|
||||||
#Make sure to update below for your relevant driver (2208 or 2209)
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||||
[tmcXXXX stepper_z3]
|
[tmcXXXX stepper_z3]
|
||||||
uart_pin: z:P1.8
|
uart_pin: z:P1.8
|
||||||
microsteps: 16
|
microsteps: 16
|
||||||
|
|
@ -267,16 +272,16 @@ stealthchop_threshold: 0
|
||||||
step_pin: P2.13
|
step_pin: P2.13
|
||||||
dir_pin: P0.11
|
dir_pin: P0.11
|
||||||
enable_pin: !P2.12
|
enable_pin: !P2.12
|
||||||
# 16 microsteps Mobius 3 ~= 0.00180
|
## 16 microsteps Mobius 3 ~= 0.00180
|
||||||
# Update value below when you perform extruder calibration
|
## Update value below when you perform extruder calibration
|
||||||
# Higher value means less filament extruded
|
## Higher value means less filament extruded
|
||||||
# If you ask for 100mm of filament, but in reality it is 98mm:
|
## If you ask for 100mm of filament, but in reality it is 98mm:
|
||||||
# step_distance = 98 / 100 * step_distance_old
|
## step_distance = 98 / 100 * step_distance_old
|
||||||
step_distance: 0.00180180
|
step_distance: 0.00180180
|
||||||
nozzle_diameter: 0.400
|
nozzle_diameter: 0.400
|
||||||
filament_diameter: 1.75
|
filament_diameter: 1.75
|
||||||
heater_pin: P2.7
|
heater_pin: P2.7
|
||||||
#Validate the following thermistor type to make sure it is correct
|
## Validate the following thermistor type to make sure it is correct
|
||||||
sensor_type: NTC 100K beta 3950
|
sensor_type: NTC 100K beta 3950
|
||||||
sensor_pin: P0.24
|
sensor_pin: P0.24
|
||||||
smooth_time: 3.0
|
smooth_time: 3.0
|
||||||
|
|
@ -288,13 +293,13 @@ control = pid
|
||||||
pid_kp = 26.213
|
pid_kp = 26.213
|
||||||
pid_ki = 1.304
|
pid_ki = 1.304
|
||||||
pid_kd = 131.721
|
pid_kd = 131.721
|
||||||
# PA can be disabled by declaring a 0.0 value
|
## Try to keep pressure_advance below 1.0
|
||||||
pressure_advance: 0.0
|
pressure_advance: 0.0
|
||||||
# Time seconds to look ahead for PA moves default is 0.010 or 10ms
|
## Default is 0.040, leave stock
|
||||||
pressure_advance_lookahead_time: 0.010
|
pressure_advance_smooth_time: 0.040
|
||||||
|
|
||||||
#E0 on MCU X/Y
|
## E0 on MCU X/Y
|
||||||
#Make sure to update below for your relevant driver (2208 or 2209)
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
||||||
[tmcXXXX extruder]
|
[tmcXXXX extruder]
|
||||||
uart_pin: P1.9
|
uart_pin: P1.9
|
||||||
microsteps: 16
|
microsteps: 16
|
||||||
|
|
@ -308,12 +313,11 @@ stealthchop_threshold: 0
|
||||||
# Probe
|
# Probe
|
||||||
#####################################################################
|
#####################################################################
|
||||||
|
|
||||||
|
|
||||||
[probe]
|
[probe]
|
||||||
# Inductive Probe
|
## Inductive Probe
|
||||||
# This probe is not used for Z height, only Quad Gantry Leveling
|
## This probe is not used for Z height, only Quad Gantry Leveling
|
||||||
# Z_MAX on mcu_z
|
## Z_MAX on mcu_z
|
||||||
# If your probe is NO instead of NC, add change pin to !z:P1.24
|
## If your probe is NO instead of NC, add change pin to !z:P1.24
|
||||||
pin: z:P1.24
|
pin: z:P1.24
|
||||||
x_offset: 0
|
x_offset: 0
|
||||||
y_offset: 25.0
|
y_offset: 25.0
|
||||||
|
|
@ -331,26 +335,33 @@ samples_tolerance_retries: 3
|
||||||
#####################################################################
|
#####################################################################
|
||||||
|
|
||||||
[heater_fan hotend_fan]
|
[heater_fan hotend_fan]
|
||||||
# Hotend Fan - XYE board, HE1 Connector
|
## Hotend Fan - XYE board, HE1 Connector
|
||||||
pin: P2.4
|
pin: P2.4
|
||||||
max_power: 1.0
|
max_power: 1.0
|
||||||
kick_start_time: 0.5
|
kick_start_time: 0.5
|
||||||
heater: extruder
|
heater: extruder
|
||||||
heater_temp: 50.0
|
heater_temp: 50.0
|
||||||
#If you are experiencing back flow, you can reduce fan_speed
|
## If you are experiencing back flow, you can reduce fan_speed
|
||||||
#fan_speed: 1.0
|
#fan_speed: 1.0
|
||||||
|
|
||||||
[fan]
|
[fan]
|
||||||
# Print Cooling Fan - XYE board, Fan Pin
|
## Print Cooling Fan - XYE board, Fan Pin
|
||||||
pin: P2.3
|
pin: P2.3
|
||||||
kick_start_time: 0.5
|
kick_start_time: 0.5
|
||||||
#depending on your fan, you may need to increase or reduce this value
|
## Depending on your fan, you may need to increase this value
|
||||||
#if your fan will not start
|
## if your fan will not start
|
||||||
off_below: 0.13
|
off_below: 0.10
|
||||||
cycle_time: 0.001
|
cycle_time: 0.001
|
||||||
|
|
||||||
|
[heater_fan controller_fan]
|
||||||
|
## Controller fan - Z board, HE1 Connector
|
||||||
|
pin: z:P2.4
|
||||||
|
kick_start_time: 0.500
|
||||||
|
heater: heater_bed
|
||||||
|
heater_temp: 45.0
|
||||||
|
|
||||||
#[heater_fan exhaust_fan]
|
#[heater_fan exhaust_fan]
|
||||||
# Exhaust fan - Z board, HE0 Connector
|
## Exhaust fan - Z board, HE0 Connector
|
||||||
#pin: z:P2.7
|
#pin: z:P2.7
|
||||||
#max_power: 1.0
|
#max_power: 1.0
|
||||||
#shutdown_speed: 0.0
|
#shutdown_speed: 0.0
|
||||||
|
|
@ -359,24 +370,17 @@ cycle_time: 0.001
|
||||||
#heater_temp: 60
|
#heater_temp: 60
|
||||||
#fan_speed: 1.0
|
#fan_speed: 1.0
|
||||||
|
|
||||||
[heater_fan controller_fan]
|
|
||||||
# Controller fan - Z board, HE1 Connector
|
|
||||||
pin: z:P2.4
|
|
||||||
kick_start_time: 0.500
|
|
||||||
heater: heater_bed
|
|
||||||
heater_temp: 45.0
|
|
||||||
|
|
||||||
#####################################################################
|
#####################################################################
|
||||||
# Bed Heater
|
# Bed Heater
|
||||||
#####################################################################
|
#####################################################################
|
||||||
|
|
||||||
[heater_bed]
|
[heater_bed]
|
||||||
# SSR Pin - Z board, Fan Pin
|
## SSR Pin - Z board, Fan Pin
|
||||||
heater_pin: z:P2.3
|
heater_pin: z:P2.3
|
||||||
sensor_type: NTC 100K MGB18-104F39050L32
|
sensor_type: NTC 100K MGB18-104F39050L32
|
||||||
sensor_pin: z:P0.23
|
sensor_pin: z:P0.23
|
||||||
smooth_time: 3.0
|
smooth_time: 3.0
|
||||||
#Adjust Max Power so your heater doesn't warp your bed
|
## Adjust Max Power so your heater doesn't warp your bed
|
||||||
max_power: 0.6
|
max_power: 0.6
|
||||||
min_temp: 0
|
min_temp: 0
|
||||||
max_temp: 120
|
max_temp: 120
|
||||||
|
|
@ -399,67 +403,69 @@ gcode:
|
||||||
G90
|
G90
|
||||||
G0 Z5 F600
|
G0 Z5 F600
|
||||||
G28 X Y
|
G28 X Y
|
||||||
# XY Location of the Z Endstop Switch
|
## XY Location of the Z Endstop Switch
|
||||||
# Update X0 and Y0 to your values (such as X157, Y305) after going through
|
## Update X0 and Y0 to your values (such as X157, Y305) after going through
|
||||||
# Z Endstop Pin Location Definition step.
|
## Z Endstop Pin Location Definition step.
|
||||||
G0 X0 Y0 F3600
|
G0 X0 Y0 F3600
|
||||||
|
|
||||||
G28 Z
|
G28 Z
|
||||||
G0 Z10 F1800
|
G0 Z10 F1800
|
||||||
|
|
||||||
#Uncomment for for your size printer:
|
## Uncomment for for your size printer:
|
||||||
#--------------------------------------------------------------------
|
#--------------------------------------------------------------------
|
||||||
#250mm bed
|
## Uncomment for 250mm build
|
||||||
G0 X125 Y125 Z30 F3600
|
#G0 X125 Y125 Z30 F3600
|
||||||
|
|
||||||
#300mm bed
|
## Uncomment for 300 build
|
||||||
#G0 X150 Y150 Z30 F3600
|
#G0 X150 Y150 Z30 F3600
|
||||||
|
|
||||||
#350mm bed
|
## Uncomment for 350mm build
|
||||||
#G0 X175 Y175 Z30 F3600
|
#G0 X175 Y175 Z30 F3600
|
||||||
#--------------------------------------------------------------------
|
#--------------------------------------------------------------------
|
||||||
|
|
||||||
|
|
||||||
[quad_gantry_level]
|
[quad_gantry_level]
|
||||||
# Use QUAD_GANTRY_LEVEL to level a gantry.
|
## Use QUAD_GANTRY_LEVEL to level a gantry.
|
||||||
# Min & Max gantry corners - measure from nozzle at MIN (0,0) and
|
## Min & Max gantry corners - measure from nozzle at MIN (0,0) and
|
||||||
# MAX (250, 250), (300,300), or (350,350) depending on your printer size
|
## MAX (250, 250), (300,300), or (350,350) depending on your printer size
|
||||||
# to respective belt positions
|
## to respective belt positions
|
||||||
|
|
||||||
#--------------------------------------------------------------------
|
#--------------------------------------------------------------------
|
||||||
# Gantry Corners for 250mm Build
|
## Gantry Corners for 250mm Build
|
||||||
|
## Uncomment for 250mm build
|
||||||
#gantry_corners:
|
#gantry_corners:
|
||||||
# -60,-10
|
# -60,-10
|
||||||
# 310, 260 #Not sure about this
|
# 310, 320
|
||||||
# Probe points
|
## Probe points
|
||||||
#points:
|
#points:
|
||||||
# 60,60
|
# 50,25
|
||||||
# 60,200
|
# 50,175
|
||||||
# 200,200
|
# 200,175
|
||||||
# 200,60
|
# 200,25
|
||||||
|
|
||||||
# Gantry Corners for 300mm Build
|
## Gantry Corners for 300mm Build
|
||||||
|
## Uncomment for 300mm build
|
||||||
#gantry_corners:
|
#gantry_corners:
|
||||||
# -60,-10
|
# -60,-10
|
||||||
# 360,310
|
# 360,370
|
||||||
# Probe points
|
## Probe points
|
||||||
#points:
|
#points:
|
||||||
# 60,60
|
# 50,25
|
||||||
# 60,240
|
# 50,225
|
||||||
# 240,240
|
# 250,225
|
||||||
# 240,60
|
# 250,25
|
||||||
|
|
||||||
# Gantry Corners for 350mm Build
|
## Gantry Corners for 350mm Build
|
||||||
|
## Uncomment for 350mm build
|
||||||
#gantry_corners:
|
#gantry_corners:
|
||||||
# -60,-10
|
# -60,-10
|
||||||
# 410,360
|
# 410,420
|
||||||
# Probe points
|
## Probe points
|
||||||
#points:
|
#points:
|
||||||
# 60,60
|
# 50,25
|
||||||
# 60,290
|
# 50,275
|
||||||
# 290,290
|
# 300,275
|
||||||
# 290,60
|
# 300,25
|
||||||
|
|
||||||
#--------------------------------------------------------------------
|
#--------------------------------------------------------------------
|
||||||
speed: 100
|
speed: 100
|
||||||
|
|
@ -472,11 +478,11 @@ max_adjust: 10
|
||||||
# Displays
|
# Displays
|
||||||
#####################################################################
|
#####################################################################
|
||||||
|
|
||||||
# Uncomment the display that you have. Display connects to Z MCU
|
## Uncomment the display that you have. Display connects to Z MCU
|
||||||
#--------------------------------------------------------------------
|
#--------------------------------------------------------------------
|
||||||
|
|
||||||
#[display]
|
#[display]
|
||||||
# RepRapDiscount 128x64 Full Graphic Smart Controller
|
## RepRapDiscount 128x64 Full Graphic Smart Controller
|
||||||
#lcd_type: st7920
|
#lcd_type: st7920
|
||||||
#cs_pin: z:P1.19
|
#cs_pin: z:P1.19
|
||||||
#sclk_pin: z:P1.20
|
#sclk_pin: z:P1.20
|
||||||
|
|
@ -485,25 +491,29 @@ max_adjust: 10
|
||||||
#encoder_pins: ^z:P3.26, ^z:P3.25
|
#encoder_pins: ^z:P3.26, ^z:P3.25
|
||||||
#click_pin: ^!z:P0.28
|
#click_pin: ^!z:P0.28
|
||||||
|
|
||||||
|
#[output_pin beeper]
|
||||||
|
#pin: z:P1.30
|
||||||
|
|
||||||
#--------------------------------------------------------------------
|
#--------------------------------------------------------------------
|
||||||
|
|
||||||
#[display]
|
#[display]
|
||||||
# "mini12864 LCD Display
|
## mini12864 LCD Display
|
||||||
#lcd_type: uc1701
|
#lcd_type: uc1701
|
||||||
#cs_pin: z:P1.18
|
#cs_pin: z:P1.18
|
||||||
#a0_pin: z:P1.19
|
#a0_pin: z:P1.19
|
||||||
#encoder_pins: z:^P3.26,z:^P3.25
|
#encoder_pins: ^z:P3.25,^z:P3.26
|
||||||
#click_pin: z:^!P0.28
|
#click_pin: ^!z:P0.28
|
||||||
#contrast: 63
|
#contrast: 63
|
||||||
|
|
||||||
#[neopixel my_neopixel]
|
#[neopixel my_neopixel]
|
||||||
#To control Neopixel RGB in mini12864 display
|
## To control Neopixel RGB in mini12864 display
|
||||||
#pin: z:P1.21
|
#pin: z:P1.21
|
||||||
#chain_count: 3
|
#chain_count: 3
|
||||||
#initial_RED: 0.1
|
#initial_RED: 0.1
|
||||||
#initial_GREEN: 0.5
|
#initial_GREEN: 0.5
|
||||||
#initial_BLUE: 0.0
|
#initial_BLUE: 0.0
|
||||||
#color_order_GRB: False
|
#color_order_GRB: False
|
||||||
|
|
||||||
#--------------------------------------------------------------------
|
#--------------------------------------------------------------------
|
||||||
|
|
||||||
|
|
||||||
|
|
@ -541,56 +551,11 @@ gcode:
|
||||||
G0 X125 Y250 F3600 ; park nozzle at rear
|
G0 X125 Y250 F3600 ; park nozzle at rear
|
||||||
BED_MESH_CLEAR
|
BED_MESH_CLEAR
|
||||||
|
|
||||||
|
## Thermistor Types
|
||||||
#[gcode_macro LOAD_FILAMENT]
|
## "EPCOS 100K B57560G104F"
|
||||||
#gcode:
|
## "ATC Semitec 104GT-2"
|
||||||
# M83 ; set extruder to relative
|
## "NTC 100K beta 3950"
|
||||||
# G1 E750 F1800 ; quickly load filament to down bowden
|
## "Honeywell 100K 135-104LAG-J01"
|
||||||
# G1 E30 F300 ; slower extrusion for hotend path
|
## "NTC 100K MGB18-104F39050L32" (Keenovo Heater Pad)
|
||||||
# G1 E15 F150 ; prime nozzle with filament
|
## "AD595"
|
||||||
# M82 ; set extruder to absolute
|
## "PT100 INA826"
|
||||||
|
|
||||||
#[gcode_macro UNLOAD_FILAMENT]
|
|
||||||
#gcode:
|
|
||||||
# M83 ; set extruder to relative
|
|
||||||
# G1 E10 F300 ; extrude a little to soften tip
|
|
||||||
# G1 E-780 F1800 ; retract filament completely
|
|
||||||
# M82 ; set extruder to absolute
|
|
||||||
|
|
||||||
|
|
||||||
# Sensor Types
|
|
||||||
# "EPCOS 100K B57560G104F"
|
|
||||||
# "ATC Semitec 104GT-2"
|
|
||||||
# "NTC 100K beta 3950"
|
|
||||||
# "Honeywell 100K 135-104LAG-J01"
|
|
||||||
# "NTC 100K MGB18-104F39050L32" (Keenovo Heater Pad)
|
|
||||||
# "AD595"
|
|
||||||
# "PT100 INA826"
|
|
||||||
|
|
||||||
# BED_MESH_CALIBRATE
|
|
||||||
# Do not use unless absolutely necessary
|
|
||||||
#[bed_mesh]
|
|
||||||
#speed: 200
|
|
||||||
#horizontal_move_z: 10
|
|
||||||
#probe_count: 7,7
|
|
||||||
#fade_start: 0.6
|
|
||||||
#fade_end: 25.0
|
|
||||||
#split_delta_z: .01
|
|
||||||
#move_check_distance: 3
|
|
||||||
#mesh_pps: 0,0
|
|
||||||
#algorithm: bicubic
|
|
||||||
#relative_reference_index: 24
|
|
||||||
|
|
||||||
#For 250mm Size:
|
|
||||||
#min_point: 40,10
|
|
||||||
#max_point: 210,180
|
|
||||||
|
|
||||||
#For 300mm Size:
|
|
||||||
#min_point: 40,10
|
|
||||||
#max_point: 260,230
|
|
||||||
|
|
||||||
#For 350mm Size:
|
|
||||||
#min_point: 40,10
|
|
||||||
#max_point: 310,280
|
|
||||||
|
|
||||||
|
|
||||||
|
|
|
||||||
Loading…
Reference in New Issue