V2 endstop relocation for stock 2.4 or Pinned AB Drives and also pinned X Y Joints for Arks MGN12 mod (#278)

* added files for Y endstop relocation

* Update README.md

* Update README.md

* removed extra file and fixed orientation

* changed folder name, added new files

* Update README.md

* Update README.md

* Update README.md

* Update README.md

* removed duplicate file

* added MGN12 Version of the Pinned XY joints to work with Arks MGN12 mod

* added MGN12 Pinned XY joints, removed umbilical stuff as thats not ready to be merged yet, moved the endstop relocation files all together in thier own folder, updated all the readmes for both mods

added MGN12 Pinned XY joints, moved the endstop relocation files all together in thier own folder and linked each mod to eachother , updated all the readmes for both mods

* Update README.md

* Update README.md

* update readmes, fixed file orientation

printer_mods/README.md

@@ -86,6 +86,7 @@ like so:
 | | [Voron0_ExtendedLegs](./hartk1213/Voron0_ExtendedLegs) | New extended legs to raise the printer up a tiny bit more  | :heavy_check_mark:| :x: | :x: |:x:|
 | | [Voron0_ExtrusionSkirt](./hartk1213/Voron0_ExtrusionSkirt) | Created a new skirt design that uses 50mm extrusions as legs and it has a c14 power inlet hole on the bottom   | :heavy_check_mark:| :x: | :x: |:x:|
 | | [Voron2.4_Pins_Mod](./hartk1213/Voron2.4_Pins_Mod) | This mod replaces all the M5 screws for all idlers/pulleys/bearings with 5mm pins  | :x:| :x: | :heavy_check_mark: |:x:|
+| | [Voron2.4_Y_Endstop_Relocation](./hartk1213/Voron2.4_Y_Endstop_Relocation) | This mod relocates the Y endstop to the top A drive piece, to work with Arkeets MGN12 mod  | :x:| :x: | :heavy_check_mark: |:x:|
 | hernsl | [Bottom Panel Mag Clip](./hernsl/bottom_panel_mag_clip) | v2.4 magnetic clips to retain bottom panel | :x: | :x: | :heavy_check_mark: |:x:|
 |hijax_pl_ |[Corner panel clip](./hijax_pl/corner_panel_clip) |V2 panel corner frames using 3-way L brackets in the corners |:x: |:x: |:heavy_check_mark: |:x:|
 | |[Din Rail mount](./hijax_pl/din_rail_mount) |Adapter to attach DIN Rail to 2020 extrusion. |:x: |:x: |:heavy_check_mark: |:x:|

printer_mods/hartk1213/Voron2.4_Pins_Mod/README.md

@@ -8,7 +8,6 @@ The pins have replaced m5 screws, at any location where the screw acts like a sh
 To complete this mod the following files will need to be reprinted 
 
 **A and B drive units**
-
  - a_drive_frame_lower_pinned.stl 
  - a_drive_frame_upper_pinned.stl 
  - b_drive_frame_lower_pinned.stl 
@@ -19,10 +18,19 @@ To complete this mod the following files will need to be reprinted
 - [a]_b_tensioner_pinned.stl
 
 **XY Joints**
+
+*NOTE: There are now 2 versions of these files , 1 set for Stock 2.4 and 1 set for  [Arkeets MGN12](../../arkeet/mgn12)*
 - xy_joint_left_upper_pinned.stl
 - xy_joint_left_lower_pinned.stl
 - xy_joint_right_upper_pinned.stl
 - xy_joint_right_lower_pinned.stl
+- 
+or 
+
+- MGN12_xy_joint_left_upper_pinned.stl
+- MGN12_xy_joint_left_lower_pinned.stl
+- MGN12_xy_joint_right_upper_pinned.stl
+- MGN12_xy_joint_right_lower_pinned.stl
 
 **Z Idlers**
 either one of these based on if you are using 6mm or 9mm belt
@@ -36,6 +44,11 @@ here is what the XY Joint will look like
 ![XY Joint](Images/1.png) 
 
 
+There is a new file for the A Drive to go along with [Arkeets MGN12](../../arkeet/mgn12) mod that has the X endstop on the toolhead 
+
+the files for the endstop relocation mod are here [Voron2.4_Y_Endstop_Relocation](../Voron2.4_Y_Endstop_Relocation)
+
+
 the following 5mm Pin hardware is what is needed as well 
 
 **BOM**

printer_mods/hartk1213/Voron2.4_Y_Endstop_Relocation/README.md

@@ -0,0 +1,26 @@
+This mod moves the Y endstop to the A drive, to go along with [Arkeet's MGN12 mod](../../arkeet/mgn12)
+that has the X endstop on the toolhead.  This mod requires a 2 pin JST-XH to be soldered to the
+switch.  The best way I have done it is to solder the wires to the JST-XH first, install it with a dab
+of super glue, then solder the wires to the Omron switch.
+
+
+There are 2 different files
+
+non pinned version
+- a_drive_frame_upper_with_jst_y_endstop.stl
+
+pinned version (since this mod also works with the [Voron2.4_Pins_Mod](../Voron2.4_Pins_Mod)):
+- a_drive_frame_upper_with_jst_y_endstop_pinned.stl
+
+here are a few pics for reference
+
+![A Drive](Images/1.png)
+
+![A Drive With JST](Images/2.png)
+
+![Jst with Wires](Images/3.png)
+
+you might need to bend the pins a little bit to get them to fit around the curve
+
+![JST with bent pins](Images/4.png)
+