diff --git a/firmware_configurations/README.md b/firmware_configurations/README.md index f46f97999..b90491d2f 100644 --- a/firmware_configurations/README.md +++ b/firmware_configurations/README.md @@ -29,6 +29,7 @@ like so: | --- | --- | --- | --- | --- | --- | --- | | jaeger | [FYSETC Spider on V1.8](./klipper/jaeger/Spider_1.1_V1.8) | Example configuration and wiring diagram for a FYSETC Spider 1.1 board on the V1.8 | :x: | :heavy_check_mark: | :x: | :x: | | MarcPot | [Fysetc Spider Board Pins](./klipper/MarcPot/fysetc_spider_pins) | Defines a set of `[board_pins]` aliases for use with the Fysetc Spider controller | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: | +| Mellow | [Fly-Super8 on V2.4](./klipper/Mellow/FLY-Super8) | Example configuration and wiring diagram for a FLY-Super8 board on the V2.4 | :x: | :x: | :heavy_check_mark: | :x: | | revnull | [BTT Octopus Board Pins](./klipper/revnull/btt_octopus_pins) | Defines a set of `[board_pins]` aliases for use with the BTT Octopus controller | :grey_question: | :grey_question: | :heavy_check_mark: | :grey_question: | --- diff --git a/firmware_configurations/klipper/Mellow/FLY-Super8/FLY-Super8-Voron2.4(Klipper).cfg b/firmware_configurations/klipper/Mellow/FLY-Super8/FLY-Super8-Voron2.4(Klipper).cfg new file mode 100644 index 000000000..446ae847a --- /dev/null +++ b/firmware_configurations/klipper/Mellow/FLY-Super8/FLY-Super8-Voron2.4(Klipper).cfg @@ -0,0 +1,607 @@ +## Voron Design VORON2 250/300/350mm FLY-Super8 TMC2209 UART config + +## *** THINGS TO CHANGE/CHECK: *** +## MCU paths [mcu] section +## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file +## Z Endstop Switch location [safe_z_home] section +## Homing end position [gcode_macro G32] section +## Z Endstop Switch offset for Z0 [stepper_z] section +## Probe points [quad_gantry_level] section +## Min & Max gantry corner postions [quad_gantry_level] section +## PID tune [extruder] and [heater_bed] sections +## Fine tune E steps [extruder] section + +##========================== Pin Definitions ======================== +## X +## Drive0_STEP_PIN PE2 +## Drive0_DIR_PIN PC5 +## Drive0_ENABLE_PIN PF11 +## Drive0_STOP_PIN PG12 #IO0 +## Drive0_UART_PIN PC4 + +## Y +## Drive1_STEP_PIN PE3 +## Drive1_DIR_PIN PF13 +## Drive1_ENABLE_PIN PF14 +## Drive1_STOP_PIN PG11 #IO1 +## Drive1_UART_PIN PC12 + +## E +## Drive2_STEP_PIN PE4 +## Drive2_DIR_PIN PG0 +## Drive2_ENABLE_PIN PG1 +## Drive2_STOP_PIN PG10 #IO2 +## Drive2_UART_PIN PF15 + +## Z +## Drive3_STEP_PIN PE14 +## Drive3_DIR_PIN PE8 +## Drive3_ENABLE_PIN PE9 +## Drive3_UART_PIN PE7 + +## Z1 +## Drive4_STEP_PIN PE15 +## Drive4_DIR_PIN PE11 +## Drive4_ENABLE_PIN PF2 +## Drive4_UART_PIN PE10 + +## Z2 +## Drive5_STEP_PIN PE1 +## Drive5_DIR_PIN PF0 +## Drive5_ENABLE_PIN PC15 +## Drive5_UART_PIN PF1 + +## Z3 +## Drive6_STEP_PIN PE0 +## Drive6_DIR_PIN PG3 +## Drive6_ENABLE_PIN PG4 +## Drive6_UART_PIN PG2 + +## Drive7_STEP_PIN PE6 +## Drive7_DIR_PIN PG6 +## Drive7_ENABLE_PIN PG7 +## Drive7_UART_PIN PG5 + +## TMC SPI MODE +## TMC MOSI PB4 +## TMC MISO PB5 +## TMC SCK PB3 + +## HEAT0 PB0 +## HEAT1 PB1 +## HEAT2 PC7 +## HEAT3 PF7 +## HEAT4 PF6 + +## BED PE5 + +## TH0 (H0 Temp) PF4 #ADC0 +## TH1 (H1 Temp) PF5 #ADC1 +## TH2 (H2 Temp) PF9 #ADC2 +## TH3 (H3 Temp) PF10 #ADC3 +## TH4 (H4 Temp) PC0 #ADC4 +## TB (Bed Temp) PC1 #ADC5 + +## FAN0 PA0 +## FAN1 PA1 +## FAN2 PA2 +## FAN3 PA3 +## FAN4 PA15 +## FAN5 PB11 +## FAN6 PB10 +## FAN7 PD12 +## FAN8 PD14 +## FAN9 PD15 + +## SERVO PC6 #BLTOUCH +## PROBE PC3 #BLTOUCH + +##加速度计 +########################################## +# 5V # GND # PD0 # PD1 # PD3 # PD4 # PD5 # +########################################## + + + + +##=================================================================== + +[mcu] +## MCU for X/Y/E steppers main MCU +## [X in X] - B Motor +## [Y in Y] - A Motor +## [E in E0] - Extruder +## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify +##-------------------------------------------------------------------- +serial: /dev/serial/by-id/usb-Klipper_stm32_00000-if00 +##-------------------------------------------------------------------- + + +[printer] +kinematics: corexy +max_velocity: 300 +max_accel: 3000 #Max 4000 +max_z_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V +max_z_accel: 350 +square_corner_velocity: 5.0 + +##################################################################### +# X/Y Stepper Settings +##################################################################### + +[stepper_x] +## Connected to X on mcu_xye (B Motor) +step_pin: PE2 +dir_pin: !PC5 +enable_pin: !PF11 +rotation_distance: 40 +microsteps: 16 +full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper +endstop_pin: PG12 +position_min: 0 +##-------------------------------------------------------------------- + +## Uncomment below for 250mm build +#position_endstop: 250 +#position_max: 250 + +## Uncomment for 300mm build +#position_endstop: 300 +#position_max: 300 + +## Uncomment for 350mm build +#position_endstop: 350 +#position_max: 350 + +##-------------------------------------------------------------------- +homing_speed: 25 #Max 100 +homing_retract_dist: 5 +homing_positive_dir: true + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_x] +uart_pin: PC4 +interpolate: True +run_current: 0.8 +hold_current: 0.7 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +[stepper_y] +## Connected to Y on mcu_xye (A Motor) +step_pin: PE3 +dir_pin: !PF13 +enable_pin: !PF14 +rotation_distance: 40 +microsteps: 16 +full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper +endstop_pin: PG11 +position_min: 0 +##-------------------------------------------------------------------- + +## Uncomment for 250mm build +#position_endstop: 250 +#position_max: 250 + +## Uncomment for 300mm build +#position_endstop: 300 +#position_max: 300 + +## Uncomment for 350mm build +#position_endstop: 350 +#position_max: 350 + +##-------------------------------------------------------------------- +homing_speed: 25 #Max 100 +homing_retract_dist: 5 +homing_positive_dir: true + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_y] +uart_pin: PF12 +interpolate: True +run_current: 0.8 +hold_current: 0.7 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +##################################################################### +# Z Stepper Settings +##################################################################### + +## Z MCU - In X Position +## Z0 Stepper - Front Left +[stepper_z] +step_pin: PE14 +dir_pin: !PE8 +enable_pin: !PE9 +rotation_distance: 40 +gear_ratio: 80:16 +microsteps: 16 +endstop_pin: PG10 +## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0) +## (+) value = endstop above Z0, (-) value = endstop below +## Increasing position_endstop brings nozzle closer to the bed +## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config +position_endstop: -0.5 +##-------------------------------------------------------------------- + +## Uncomment below for 250mm build +#position_max: 240 + +## Uncomment below for 300mm build +#position_max: 290 + +## Uncomment below for 350mm build +#position_max: 340 + +##-------------------------------------------------------------------- +position_min: -5 +homing_speed: 8 +second_homing_speed: 3 +homing_retract_dist: 3 + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_z] +uart_pin: PE7 +interpolate: true +run_current: 0.8 +hold_current: 0.8 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +## Z MCU - In Y Position +## Z1 Stepper - Rear Left +[stepper_z1] +step_pin: PE15 +dir_pin: PE11 +enable_pin: !PF2 +rotation_distance: 40 +gear_ratio: 80:16 +microsteps: 16 + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_z1] +uart_pin: PE10 +interpolate: true +run_current: 0.8 +hold_current: 0.8 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +## Z MCU - In Z Position +## Z2 Stepper - Rear Right +[stepper_z2] +step_pin: PE1 +dir_pin: !PF0 +enable_pin: !PC15 +rotation_distance: 40 +gear_ratio: 80:16 +microsteps: 16 + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_z2] +uart_pin: PF1 +interpolate: true +run_current: 0.8 +hold_current: 0.80 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +## Z MCU - In E0 Position +## Z3 Stepper - Front Right +[stepper_z3] +step_pin: PE0 +dir_pin: PG3 +enable_pin: !PG4 +rotation_distance: 40 +gear_ratio: 80:16 +microsteps: 16 + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_z3] +uart_pin: PG2 +interpolate: true +run_current: 0.8 +hold_current: 0.80 +sense_resistor: 0.110 +stealthchop_threshold: 0 + + +##################################################################### +# Extruder +##################################################################### + +# E0 on MCU X/Y +[extruder] +step_pin: PE4 +dir_pin: PG0 +enable_pin: !PG1 +## Update value below when you perform extruder calibration +## If you ask for 100mm of filament, but in reality it is 98mm: +## rotation_distance = * / 100 +## 22.6789511 is a good starting point +rotation_distance: 22.6789511 #Bondtech 5mm Drive Gears +## Update Gear Ratio depending on your Extruder Type +## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio) +## Use 80:20 for M4, M3.1 +gear_ratio: 50:17 #BMG Gear Ratio +microsteps: 16 +full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree +nozzle_diameter: 0.400 +filament_diameter: 1.75 +heater_pin: PB0 +## Validate the following thermistor type to make sure it is correct +sensor_type: ATC Semitec 104GT-2 +sensor_pin: PF4 +min_temp: 10 +max_temp: 270 +max_power: 1.0 +min_extrude_temp: 170 +control = pid +pid_kp = 26.213 +pid_ki = 1.304 +pid_kd = 131.721 +## Try to keep pressure_advance below 1.0 +#pressure_advance: 0.05 +## Default is 0.040, leave stock +#pressure_advance_smooth_time: 0.040 + +## E0 on MCU X/Y +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 extruder] +uart_pin: PF15 +interpolate: false +run_current: 0.5 +hold_current: 0.4 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +##################################################################### +# Bed Heater +##################################################################### + +[heater_bed] +## SSR Pin - Z board, Fan Pin +heater_pin: PE5 +sensor_type: NTC 100K beta 3950 +sensor_pin: PC1 +## Adjust Max Power so your heater doesn't warp your bed +max_power: 0.6 +min_temp: 0 +max_temp: 120 +control: pid +pid_kp: 58.437 +pid_ki: 2.347 +pid_kd: 363.769 + +##################################################################### +# Probe +##################################################################### + +[probe] +## Inductive Probe +## This probe is not used for Z height, only Quad Gantry Leveling +## Z_MAX on mcu_z +## If your probe is NO instead of NC, change pin to !^z:P0.10 +pin: ^PC3 +x_offset: 0 +y_offset: 25.0 +z_offset: 0 +speed: 10.0 +samples: 3 +samples_result: median +sample_retract_dist: 3.0 +samples_tolerance: 0.006 +samples_tolerance_retries: 3 + +##################################################################### +# Fan Control +##################################################################### + +[heater_fan hotend_fan] +## Hotend Fan - XYE board, HE1 Connector +pin: PA0 +max_power: 1.0 +kick_start_time: 0.5 +heater: extruder +heater_temp: 50.0 +## If you are experiencing back flow, you can reduce fan_speed +#fan_speed: 1.0 + +[fan] +## Print Cooling Fan - XYE board, Fan Pin +pin: PA1 +kick_start_time: 0.5 +## Depending on your fan, you may need to increase this value +## if your fan will not start. Can change cycle_time (increase) +## if your fan is not able to slow down effectively +off_below: 0.10 + +[heater_fan controller_fan] +## Controller fan - Z board, HE1 Connector +pin: PA2 +kick_start_time: 0.5 +heater: heater_bed +heater_temp: 45.0 + +#[heater_fan exhaust_fan] +## Exhaust fan - Z board, HE0 Connector +#pin: PA3 +#max_power: 1.0 +#shutdown_speed: 0.0 +#kick_start_time: 5.0 +#heater: heater_bed +#heater_temp: 60 +#fan_speed: 1.0 + +##################################################################### +# Homing and Gantry Adjustment Routines +##################################################################### + +[idle_timeout] +timeout: 1800 + +[safe_z_home] +## XY Location of the Z Endstop Switch +## Update -10,-10 to the XY coordinates of your endstop pin +## (such as 157,305) after going through Z Endstop Pin +## Location Definition step. +home_xy_position:-10,-10 +speed:100 +z_hop:10 + +[quad_gantry_level] +## Use QUAD_GANTRY_LEVEL to level a gantry. +## Min & Max gantry corners - measure from nozzle at MIN (0,0) and +## MAX (250, 250), (300,300), or (350,350) depending on your printer size +## to respective belt positions + +#-------------------------------------------------------------------- +## Gantry Corners for 250mm Build +## Uncomment for 250mm build +#gantry_corners: +# -60,-10 +# 310, 320 +## Probe points +#points: +# 50,25 +# 50,175 +# 200,175 +# 200,25 + +## Gantry Corners for 300mm Build +## Uncomment for 300mm build +#gantry_corners: +# -60,-10 +# 360,370 +## Probe points +#points: +# 50,25 +# 50,225 +# 250,225 +# 250,25 + +## Gantry Corners for 350mm Build +## Uncomment for 350mm build +#gantry_corners: +# -60,-10 +# 410,420 +## Probe points +#points: +# 50,25 +# 50,275 +# 300,275 +# 300,25 + +#-------------------------------------------------------------------- +speed: 100 +horizontal_move_z: 10 +retries: 5 +retry_tolerance: 0.0075 +max_adjust: 10 + +##################################################################### +# Displays +##################################################################### + +## Uncomment the display that you have. Display connects to Z MCU +#-------------------------------------------------------------------- + +#[display] +## RepRapDiscount 128x64 Full Graphic Smart Controller +#lcd_type: st7920 +#cs_pin: PG8 +#sclk_pin: PC14 +#sid_pin: PB2 +#menu_timeout: 40 +#encoder_pins: ^PB7, ^PB6 +#click_pin: ^!PE13 + +#[output_pin beeper] +#pin: PE12 + +#-------------------------------------------------------------------- + +#[display] +## mini12864 LCD Display +#lcd_type: uc1701 +#cs_pin: PB2 +#a0_pin: PG8 +#encoder_pins: ^PB6,^PB7 +#click_pin: ^!PE13 +#contrast: 63 + +#[neopixel fysetc_mini12864] +## To control Neopixel RGB in mini12864 display +#pin: PC13 +#chain_count: 3 +#initial_RED: 0.1 +#initial_GREEN: 0.5 +#initial_BLUE: 0.0 +#color_order: RGB + +## Set RGB values on boot up for each Neopixel. +## Index 1 = display, Index 2 and 3 = Knob +#[delayed_gcode setdisplayneopixel] +#initial_duration: 1 +#gcode: +# SET_LED LED=fysetc_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0 +# SET_LED LED=fysetc_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0 +# SET_LED LED=fysetc_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3 + +#-------------------------------------------------------------------- + + +##################################################################### +# Macros +##################################################################### + +[gcode_macro G32] +gcode: + BED_MESH_CLEAR + G28 + QUAD_GANTRY_LEVEL + G28 + ## Uncomment for for your size printer: + #-------------------------------------------------------------------- + ## Uncomment for 250mm build + #G0 X125 Y125 Z30 F3600 + + ## Uncomment for 300 build + #G0 X150 Y150 Z30 F3600 + + ## Uncomment for 350mm build + #G0 X175 Y175 Z30 F3600 + #-------------------------------------------------------------------- + +[gcode_macro PRINT_START] +# Use PRINT_START for the slicer starting script - please customise for your slicer of choice +gcode: + G32 ; home all axes + G1 Z20 F3000 ; move nozzle away from bed + + +[gcode_macro PRINT_END] +# Use PRINT_END for the slicer ending script - please customise for your slicer of choice +gcode: + M400 ; wait for buffer to clear + G92 E0 ; zero the extruder + G1 E-10.0 F3600 ; retract filament + G91 ; relative positioning + G0 Z1.00 X20.0 Y20.0 F20000 ; move nozzle to remove stringing + TURN_OFF_HEATERS + M107 ; turn off fan + G1 Z2 F3000 ; move nozzle up 2mm + G90 ; absolute positioning + G0 X125 Y250 F3600 ; park nozzle at rear + BED_MESH_CLEAR + +## Thermistor Types +## "EPCOS 100K B57560G104F" +## "ATC Semitec 104GT-2" +## "NTC 100K beta 3950" +## "Honeywell 100K 135-104LAG-J01" +## "NTC 100K MGB18-104F39050L32" (Keenovo Heater Pad) +## "AD595" +## "PT100 INA826" diff --git a/firmware_configurations/klipper/Mellow/FLY-Super8/pins.jpg b/firmware_configurations/klipper/Mellow/FLY-Super8/pins.jpg new file mode 100644 index 000000000..a96637793 Binary files /dev/null and b/firmware_configurations/klipper/Mellow/FLY-Super8/pins.jpg differ diff --git a/firmware_configurations/klipper/Mellow/FLY-Super8/readme.md b/firmware_configurations/klipper/Mellow/FLY-Super8/readme.md new file mode 100644 index 000000000..aabd82200 --- /dev/null +++ b/firmware_configurations/klipper/Mellow/FLY-Super8/readme.md @@ -0,0 +1,13 @@ +Klipper configuration of FLY-Super8 motherboard for Voron2.4 +========= + +## EN +![Pins](pins.jpg) + +[EN Docs](https://teamgloomy.github.io/fly_super8_pins.html) + + +## zh_CN +![cn v2.4 pins](voron2.4-ZH_cn.jpg) + +[CN Docs](https://docs.3dmellow.com/zh_CN/#/board/fly_super8/) diff --git a/firmware_configurations/klipper/Mellow/FLY-Super8/voron2.4-ZH_cn.jpg b/firmware_configurations/klipper/Mellow/FLY-Super8/voron2.4-ZH_cn.jpg new file mode 100644 index 000000000..07f4d0293 Binary files /dev/null and b/firmware_configurations/klipper/Mellow/FLY-Super8/voron2.4-ZH_cn.jpg differ