Rotated Pi Mount with Heatsink provisions by bryansj (#24)

* Added bryansj mods

firmware_configurations/README.md

@@ -23,6 +23,7 @@ If your mod is lacking a column in the compatibility matrix, feel free to submit
 
 | Creator | Config title | Description | V1.6 | V2.1 | V2.2 |
 |---------|--------------|-------------|------|------|------|
+| bryansj  | [SKR 1.3 V2.2 Extra Settings for Reference](./klipper/bryansj) | Voron Design VORON2.2 300mm SKR 1.3 TMC2209 config with Extra Features Enabled for Reference | :x: | :grey_question: | :heavy_check_mark: |
 | Chron   | [SKR 1.3 TMC2208 UART Config](./klipper/Chron) | Configuration for SKR 1.3 TMC2208 UART | :x: | :heavy_check_mark: | :grey_question: |
 | Danowar  | [FYSETC F6 1.3 Klipper Config](./klipper/Danowar/FYSETC_F6_V1.3_Klipper_Config) | Klipper config for a FYSETC F6 350 build. UPDATED 11/14/19 | :x: | :heavy_check_mark: | :heavy_check_mark: |
 | eddie  | [SKR 1.3 V2 Universal Config](./klipper/eddie) | Universal Config and Setup Guide for SKR 1.3 and V2 | :x: | :heavy_check_mark: | :heavy_check_mark: |

firmware_configurations/klipper/bryansj/Readme.md

@@ -0,0 +1,21 @@
+This is my modded version of Eddie's SKR Klipper config file.
+
+* Voron Design VORON2.2 V2.291 300mm SKR 1.3 TMC2209 UART config
+* Based on Eddie's template and guide from:
+* github.com/VoronDesign/VoronUsers/tree/master/firmware_configurations/klipper/eddie
+* with the following adjustments and additions from bryansj:
+*   RepRapDiscount 128x64 Full Graphic Smart Controller
+*   Nozzle Wipe
+    *   added to G32
+*   Prime Line
+*   Extended QGL corner points
+*   Bed Meshing (Commented Out)
+*   TL Filament Run-out Sensor
+*   Chamber Temperature Thermistor (in Z vertical Chain)
+    *   linked to Back Panel Exhaust fan 
+*   Force Move Enabled
+*   Pause/Resume Enabled
+*   Homing IF/THEN to omit unneeded homing operations
+*   M117 LCD Text Added *16 Characters Max
+*   Expanded LCD Menu Options for Voron/Klipper Commands
+    *   Quad Gantry Level, Firmware_Restart, TESTZ Offsetting

printer_mods/README.md

@@ -28,6 +28,7 @@ If your mod is lacking a column in the compatibility matrix, feel free to submit
 |Armstr0ng |[Led extrusions mount](./Armstr0ng) | A mount for aluminium LED extrusions with hidden fasteners  | :grey_question:|:heavy_check_mark: | :heavy_check_mark:|
 | ArmyAg08|[Logitech Camera Mounts](./ArmyAg08/Logitech_C270_Mounts) |Different Logitech camera mounts, attached to the extrusions. Fits C270 and C310 |:heavy_check_mark: |:heavy_check_mark: |:heavy_check_mark: |
 | | [Corner Panel Clip](./ArmyAg08/Panels)|Corner panel clip that fit 3mm or 1/8" panels with foam tape | :x:|:heavy_check_mark: | :heavy_check_mark:|
+| bryansj   | [Rotated Pi Mount with Heatsink](./bryansj/RPi_Frame_with_Heatsink_90deg) | Raspberry Pi with Heatsink Frame for minimal channel width | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: |
 | blamm   | [Blind Joint Drilling Jigs](./blamm/jigs) | Jigs to drill your blind joints in the right spot | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: |
 | Cerulean   | [Respooler](./Cerulean/Respooler) | Respool tangled spools or bad koils | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: |
 |Danowar |[Dual Mobius Mount](./Danowar/Dual_Mobuis_Mount) | Mounts two Mobius Extruders to the back of the printer| :heavy_check_mark:| :heavy_check_mark:|:heavy_check_mark: |

printer_mods/bryansj/RPi_Frame_with_Heatsink_90deg/readme.md

@@ -0,0 +1 @@
+This is a mount rotated 90 degrees for a Raspberry Pi using a heatsink.  With the heatsink you need to run the fasteners from the bed side so the holes are counter-bored.  The holes are for the stock 2.5mm fasteners used for the heatsink.  Unless you have longer 2.5mm screws you will need to omit the bottom cover of the heatsink which isn't needed for cooling anyway.

printer_mods/bryansj/readme.md

@@ -0,0 +1,2 @@
+# Voron-Mods
+ bryansj Voron Mods