Voron 0.1 Neopixel Holder (#547)

* Create README.md

* Diagram

* Create Photos

* Update Photos

* Delete Untitled Sketch_bb.png

* Delete Photos

* Create Images

* Delete Images

* Create deleteme.html

* Add files via upload

* Delete deleteme.html

* Add files via upload

* Delete Untitled Sketch_bb.png

* Create rrg

* Add files via upload

* Delete rrg

* Create DD

* Add files via upload

* Delete DD

* Update README.md

* Update README.md

* Update README.md

* Update README.md

* Add files via upload

* Delete 20211113_164552.jpg

* Delete 20211113_174302.jpg

* Delete 20211113_174447.jpg

* Delete 20211113_190149.jpg

* Delete 20211114_160249.jpg

* Delete 20211114_160300.jpg

* Added Images

* Update README.md

* Added Showcase Images

* Added my mod

* Added X to Trident Column

* Update README.md

printer_mods/README.md

@@ -236,6 +236,7 @@ like so:
 |Nashuar|[V0 Dragon Toolhead M2.5x8](./Nashuar/V0_Dragon_ToolheadStockScrews) |This toolhead uses the stock M2.5 screw that came with the dragon hotend |:heavy_check_mark:|:x:|:x:|:x:|
 |natewalck |[V1.8 Jigs](./natewalck/v1.8_Jigs) |Jigs for assembling V1.8 |:x: |:heavy_check_mark: |:x: |:x:|
 | nhchiu | [V0.1 Movable Pulley Z Drive](./nhchiu/V0.1_Movable_Pulley_Z) | A movable pulley system on the Z axis with 1:8 total speed ratio for V0.1 | :heavy_check_mark: | :x: | :x: | :x: | :x: |
+| nikolasbabetas | [Neopixel Holder ](./nikolasbabetas/Neopixel_Holder) | A holder to attach Neopixel/WS2812B Led Strips to the V0.1 | :heavy_check_mark: | :x: | :x: | :x: |:x:|
 |Nomsplease |[60mm Shaft Jig](./Nomsplease/60mm_Shaft_Jig) |Simple jig for cutting and grinding 60mm Z shafts |:x: |:x: |:heavy_check_mark: |:x:|
 | |[Duet Wifi Mount](./Nomsplease/V0_Mods/duet_wifi_mount) | Duet wifi mount in pocketwatch location |:heavy_check_mark: |:x: |:x: |:x:|
 | |[LED Mounts](./Nomsplease/V0_Mods/led_mounts) | Basic LED mounts for 10 and 12mm strips |:heavy_check_mark: |:x: |:x: |:x:|

printer_mods/nikolasbabetas/Neopixel_Holder/README.md

@@ -0,0 +1,40 @@
+Neopixel Mount 
+==============================
+These are neopixel mounts that slide into the V0.1's top extrusions (20 leds in total)
+
+BOM
+---
+- Neopixel/WS2812B led strip (60 leds/m) only 34cm, 20 leds are needed
+- Cables 
+
+Instructions
+---
+- Print 4 of the "**Neopixel_Mount**" (2 for each side)
+- Solder only the 5V and GND wires on the led strips
+- Slide them into the mounts
+- Solder the signal wire based on the diagram below (There is a hole in the mount to allow the wire to go from the one strip to the other)
+- Remove the 2 screws holding each extrusion into place
+- Remove the 3 screws that attach the panels onto each extrusion
+- Slide the mounts onto each extrusion and screw the extrusions in place
+
+Neopixel Holder
+---
+![White](Images/WhiteLight.jpg)
+![Blue](Images/BlueLight.jpg)
+![Print](Images/LitUpPrint.jpg)
+![Pink](Images/PinkLightMacro.jpg)
+
+Printed Parts
+---
+![Neopixel_Holder](Images/CloseUp.jpg)
+
+Circuit Diagram
+---
+![CircuitDiagram](Images/CircuitDiagram.png)
+
+Assembly
+---
+![Extrusion](Images/Extrusion.jpg)
+![LedStripConnections](Images/LedStripConnections.jpg)
+
+