diff --git a/.github/PULL_REQUEST_TEMPLATE.md b/.github/PULL_REQUEST_TEMPLATE.md
index ffe98c020..ac4b306b3 100644
--- a/.github/PULL_REQUEST_TEMPLATE.md
+++ b/.github/PULL_REQUEST_TEMPLATE.md
@@ -5,12 +5,12 @@ highly appreciated!
 
 <!--
 Describe the submission further using the template provided below. The more
-details the better! Please don't forget to thoroughly read the mod requirements and rules below
+details the better! Please don't forget to thoroughly read the mod requirements and rules
 and make sure your mod submission adheres to these rules.
 Doing so speeds up the review process and will increase your chances at acceptance.
 -->
 
-### Which mods/configurations/profiles are added by this PR?
+### Which mods are added by this PR?
 
 ### How was it tested?
 
@@ -18,68 +18,9 @@ Doing so speeds up the review process and will increase your chances at acceptan
 
 ### Screenshots (if appropriate)
 
-### ⚠️⚠️**PLEASE CAREFULLY READ AND APPLY THE RULES BELOW**⚠️⚠️
+### ⚠️⚠️**PLEASE READ AND COMPLETE THE CHECKLIST BELOW**⚠️⚠️
 
-  * [ ] The mod, firmware configuration or slicer profile is in the correct category
-    folder. Printable mods go to `printer_mods/`, firmware configurations
-    go to `firmware_configurations/`, slicer profiles go to `slicer_profiles/`.
-    Create a subfolder with your name, and place the mods in a subfolder with
-    a descriptive name within that folder, e.g.: `/printer_mods/FHeilmann/flux_capacitor`.
-  * [ ] Folder and file naming:
-    * Folders and filenames MUST NOT contain spaces. Only letters `a-zA-Z`, numbers `0-9`, underscores `_`, hyphens `-` and periods `.`
-    * You may use the following filenames to indicate the color and quantity of your prints:
-      * Primary color: `part_xyz.stl`
-      * Accent color: `[a]_part_xyz.stl`
-      * Opaque color (Blocks light): `[o]_part_xyz.stl`
-      * Clear/transparent color (Allows light): `[c]_part_xyz.stl`
-      * Quantity, if more than one is needed: `part_xyz_x4.stl`
-  * [ ] Each mod folder must contain a `.metadata.yml` file with information about the mod.
-    Refer to the following template for the required and optional contents:
-    ```yaml
-    ---
-    title: Mod Title # required
-    description: "This mod does awesome things with awesome printers!" # required
-    mod_version: 1 # required
-    printer_compatibility:  # required, one or more of the options listed below
-      - V0
-      - V0.1
-      - V0.2
-      - V0.2r1
-      - V1
-      - V1.6
-      - V1.8
-      - V1.8r1
-      - V2
-      - V2.1
-      - V2.2
-      - V2.4
-      - V2.4r1
-      - V2.4r2
-      - VSW
-      - VT
-      - VTr1
-      - VL
-    cad: # required: At least 1 CAD file for your mod, path relative to your mod folder
-      - CAD/my_step_file_1.step
-      - CAD/my_f360_file_1.f3d
-    images: # optional, image files provided with your mod, path relative to your mod folder
-      - images/mods_site_card_image.png
-      - images/side_view.png
-      - images/install_guide.png
-    discord_username: discord_person # optional, your discord username
-    ```
-  * [ ] For each mod, add a small `README.md` file to its folder with a short description
-    of what the mod accomplishes. This readme can be used to add pictures, give assembly
-    instructions or specify a bill of materials if the mod requires additional hardware.
-  * [ ] The mod/configuration/profile has been **TESTED** by the person submitting the mod
-    and/or other Voron users. Make sure to add information about how the mod was tested below.
-  * [ ] The mod is **NOT** merely a slight modification of an official Voron part, configuration
-    or profile (i.e. an official Voron part with a few mm added or removed or a slicer profile
-    which only modifies a few values). *(When in doubt, contact one of the admins in the
-    Voron discord before submitting the PR)*
-  * [ ] Submitted STLs are **printable without support and oriented properly**. If supports can't be avoided,
-    the model must include break-away supports.
-  * [ ] Submitted STL files are **not corrupt**. *(This can be tested by opening the STL in PrusaSlicer
-    and checking if mesh errors are reported.)*
-  * [ ] Submissions **must** include a CAD file in the form of a `.STEP`, `.F3D` or `.SCAD` file
-  * [ ] Submitted firmware configs or slicer profiles **contain no sensitive data** (e.g. API keys).
+  * [ ] I have read the rules available [here](https://github.com/VoronDesign/VoronUsers/wiki/Mod-Submission-Rules) and
+        my mod adheres to these rules.
+  * [ ] This mod was created by myself and I agree to publish it under the repository
+        [license](https://github.com/VoronDesign/VoronUsers/blob/master/LICENSE.md)