Skirt-mounted power switch for 2.4 (#760)

* Skirt-mounted power switch for 2.4

* Fixed a typo

* Fixed headings in readme

printer_mods/README.md

@@ -332,6 +332,7 @@ like so:
 |  | [Extrusion/Chamber Thermistor Mount](./samwiseg0/extrusion_thermistor_mount) | Extrusion mount for a NTC100K Thermistor extrusion | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: |
 |  | [Corsair Flash Voyager GTX Din Mount](./samwiseg0/voyager_gtx_din_mount) | Din carrier for a Corsair Flash Voyager GTX | :x: | :grey_question: | :heavy_check_mark: | :x: | :heavy_check_mark: |
 | scanlory | [Clip-On Front Door Frame](./scanlory/clip_on_door_frame) | Clip-on frame to stiffen and seal front door panels when using modified hinges. | :x: | :x: | :heavy_check_mark: |:x:| :x: |
+| ScramblerUSA | [Side Skirt Power Switch](./ScramblerUSA/SideSkirtPowerSwitch) | Skirt-mounted rocker switch for easy access for Voron 2.4 | :x: | :x: | :heavy_check_mark: | :x: | :x: |
 | See1807 | [TopHat Exhaust and LED Light](./See1807/Voron_V0_Exhaust_and_LED_Mod) | A mount for 10mm LED strips and Exhaust for Voron V0 | :heavy_check_mark: | :x: | :x: | :x: |
 | ShinyPants | [OrangePi 3 LTS DIN Rail bracket](./ShinyPants/Orange_Pi_3_LTS_DIN) | A DIN rail mount for OrangePi LTS 3 | :x: | :heavy_check_mark: | :heavy_check_mark: | :x: | :heavy_check_mark: |
 | Shteeeeeve | [V0.1 LED Tophat](./Shteeeeeve/V01-LED-Tophat) | V0.1 LED Tophat w/ 24V LED Lightstrip | :heavy_check_mark: | :x: | :x: | :x: |

printer_mods/ScramblerUSA/SideSkirtPowerSwitch/README.md

@@ -0,0 +1,36 @@
+# Side Skirt Power Switch
+
+A mount for the GSW-42 rocker switch in the skirt element to allow easy access to a power switch without reaching behind the printer and trying to find it by touch.
+Can be substituted with GSW-41 if you don't want it to glow red when turned on.
+
+
+## Parts Required
+
+* (1) GSW-42 illuminated rocker switch
+* Some mains wire
+* Spade crimp connectors
+* Butt crimp connectors
+
+## Printing
+
+* Print as is for the "a" skirt (rear left/front right) or mirror the part to get the "b" variant.
+
+## Installation
+
+* Remove existing skirt element.
+* Attach the new skirt element re-using the same M3x8 screw.
+* Prepare the wires to your liking (unplug from existing switch or splice into existing wiring). You will need 3 wires: line, load, neutral.
+* Fish the wires through the hole.
+* Connect the switch. The GSW-42 switch is connected like so: pin 1 goes to line (plug), pin 2 goes to load (power supply), pin 3 (brass pin) is connected to neutral.
+* Snap the switch into the hole.
+* Enjoy easy access to the power switch.
+
+## Sourcing
+
+* Switch is available in Home Depot (https://www.homedepot.com/p/Gardner-Bender-16-Amp-Single-Pole-Rocker-Switch-GSW-42/206061064) or Amazon (https://www.amazon.com/Gardner-Bender-GSW-42-Electrical-Illuminated/dp/B00004WLKI) or even in Walmart.
+* Wires/connectors you most likely already have from building the printer :)
+
+
+![](./images/SkirtPower.png)
+
+![](./images/SkirtPower-photo.png)