Magnetic Panels with Magnet Inserts (#736)

* Create README.md

* Create README.md

* Create README.md

* Adding STLs

Adding STLs for corner and mid panel clips in 4mm and 6mm variations, magnet inserts and unhammer, installation jig.

* Delete README.md

* Delete README.md

* Adding README.md content

Description and photos.

* Create README.md

* Adding images

* Create README.md

* Create README.md

* Update README.md

Initial content with description and images

* Create README.md

* Create README.md

* Adding images for Magnetic Panel mod

* Update README.md

* Adding STLs for Magnetic Panels with Magnet Inserts

* Delete printer_mods/Le0n/OV5648 Mount directory

* Delete README.md

* Create README.md

* Add files via upload

* Delete README.md

* Adding Le0n/Magnetic_Panels_with_Magnet_Inserts

* Delete printer_mods/leang directory

* Update README.md

* Upated STL and README

Added Magnet-Insert-Side.stl for easier printing.

* Update README.md

* Add files via upload

Adding slightly taller variant.

* Renaming file for consistency

Renaming file for consistency

* Delete README.md

printer_mods/Le0n/Magnetic_Panels_with_Magnet_Inserts/README.md

@@ -0,0 +1,32 @@
+![Magnetic Panels with Magnet Inserts](Images/magnetic-panel-and-inserts-0-installed-2.jpg)
+
+## Magnetic Panels with Magnet Inserts
+
+There are various panel latches and magnetic clips that offer quick panel removal for swapping between enclosed- and open-chamber printing, but I wanted to fix a few of the pain points that I ran into with some of the existing mods.
+
+* Does not require a lot of filament. The corner and mid-panel clips were modeled after the stock Trident panel clips and are similarly hollowed, saving filament and print time.
+
+* Uses a thin strip of VHB to adhere to the panels. This should provide (1) solid adhesion without the need for drilling or extra fasteners, (2) some amount of squish for the magnets to pull against, and (3) the ability to adjust or remove them in the future.
+
+* The frame magnet inserts are designed to (1) require only printed parts and no additional fasteners aside from the 6x3 magnets, (2) sit inside the frame slot flush against the aluminum frame face, (3) be easily adjustable, and (4) retain the magnets without glue and allow removal for correcting polarity or salvaging. Discord@PF VT.520 came up with the idea of using a hammerhead-style rotating nut to tighten and press against the magnet insert, holding it in place. There are two included versions of the inserts. *Magnet-Insert.stl* is the original design but may be slightly more difficult to print due to the bridging involved. *Magnet-Insert-Side.stl* is redesigned for easier printing; namely, reoriented on its side, uses 45° chamfers rather than fillets, and does not require bridging.
+
+* The panel's ability to sit right up to the face of the frame allows the panels to pop on and off without any interference.
+
+* The only required parts are a small amount of VHB tape and a lot of magnets (48 6x3mm magnets for each panel).
+
+*Magnet inserts hold two 6x3 magnets and is held in the aluminum extrusion with an unhammer*
+![Magnetic Panels with Magnet Inserts](Images/magnetic-panel-and-inserts-1-magnet-insert.png)
+
+![Magnetic Panels with Magnet Inserts](Images/magnetic-panel-and-inserts-2-inserts-in-frame-1.png)
+
+![Magnetic Panels with Magnet Inserts](Images/magnetic-panel-and-inserts-3-inserts-in-frame-2.png)
+
+*The corner and mid-panel clips hold matching 6x3 magnets*
+![Magnetic Panels with Magnet Inserts](Images/magnetic-panel-and-inserts-4-clips-underside.png)
+
+![Magnetic Panels with Magnet Inserts](Images/magnetic-panel-and-inserts-5-full-install.png)
+
+*Installation jig makes it easy to set the proper spacing for corner inserts*
+![Magnetic Panels with Magnet Inserts](Images/magnetic-panel-and-inserts-6-jig.png)
+
+![Magnetic Panels with Magnet Inserts](Images/magnetic-panel-and-inserts-0-installed-1.jpg)

printer_mods/README.md

@@ -235,6 +235,7 @@ like so:
 | |[V0 Printed Deck with inserts](./Kruppes/Deck_Panel_inserts_logo) |Electronics Deck Panel using brass heat inserts. Optional with accent color Voron Logo. |:heavy_check_mark: |:x: |:x: |:x:|
 | Kyleisah |[CableGator Cable Comb](./Kyleisah/CableGator) | A cable comb for simplifying and tidying wire harnesses for printers with drag chains |:heavy_check_mark:|:heavy_check_mark:|:heavy_check_mark:|:heavy_check_mark:|:heavy_check_mark:|
 | lakai | [Bruag Skirts](./lakai/Bruag_Skirts) | V2 350mm skirts inspired by Bruag Facades | :x: | :x: | :heavy_check_mark: | :x: |
+|Le0n|[Magnetic panels with Magnet Inserts](./Le0n/Magnetic_Panels_with_Magnet_Inserts)| Magnetic panel mounts with magnets inserted into frame slots. |:x:|:heavy_check_mark:|:heavy_check_mark:|:x:|:heavy_check_mark:|
 |leandromarceddu|[PowerSkirt](./leandromarceddu/PowerSkirt) |Modified skirtpiece for a digital power monitor|:x:|:grey_question:|:heavy_check_mark:|:grey_question:|
 |littleferris |[V0 c14 Skirt Inlet](./littleferris/V0_Skirt_Inlet) |V0 C14 Skirt inlet |:heavy_check_mark: |:x: |:x: |:x:|
 | LJ | [Scrubby](./LJ/Scrubby) | Easy to use filament dust filter | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark:|