6mm slot cover (#576)

* 6mm slot cover

Simple cover for extrusions with 6mm slot width to prevent intrusion of dust and leaked fused filamet

* update

* update

* Delete slot_cover.3mf

* Delete slot_cover_one_side.3mf

* Update README.md

* Update README.md

Moved at the bottom of the file as required

* Update README.md

Moved under the following line:
| | LGX Lite toolhead PCB mount | Mount for Hartk's toolhead PCB(s) for LGX Lite | ❌ | ✔️ | ✔️ | ✔️ | ✔️ |

printer_mods/README.md

@@ -138,6 +138,7 @@ like so:
 | | [Exhaust_cover](./Fiction/Exhaust_cover) | Cover for exhaust cutout in back panel | :x: | :x: | :heavy_check_mark: | :x: | :heavy_check_mark: |
 | | [Exhaust_cover_SFS](./Fiction/Exhaust_cover_SFS) | Exhaust cover and BTT Smart Filament Sensor mount | :x: | :x: | :heavy_check_mark: | :x: | :heavy_check_mark: |
 | | [LGX Lite toolhead PCB mount](./Fiction/LGX_Lite_toolhead_PCB_mount) | Mount for Hartk's toolhead PCB(s) for LGX Lite | :x: | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: |
+| filotto78 | [6mm slot cover](./filotto78/6mm_slot_cover) | Simple cover for extrusion with 6mm slot width | :x: | :grey_question: | :heavy_check_mark: |:grey_question:| :grey_question:|
 | FreeformFez | [V1.8 Filtered Power Inlet](./FreeformFez/FilteredPower) | V1.6 Filtered Inlet and Rocker Switch for V1.8 | :x: | :heavy_check_mark: | :x: |:x:|
 | GadgetAngel | [Cricut Voron Logos](./GadgetAngel/Cricut_Voron_Logos) |For any cutting machines or machines that rely on vector graphics and use .svg files. These vectors or .svg files are the Voron Design Logos for the Voron 2.4, Voron SwitchWire, Voron 0.0/0.1. and Trident These .svg files use a minimal amount of anchor points to achieve the vector shapes! | :heavy_check_mark: | :x: | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: |
 |  | [Bed Support Extrusions Alignment Tools](./GadgetAngel/Bed_Support_Alignment_Tools) |The bed support alignment tools will assist in helping align the "bed support extrusions" to the frame. When the alignment tools are placed in all four corners of the Voron Printer's frame the "bed support extrusions" will butt up against these tools so that you can screw the "bed support extrusions" down to the printer's frame in the correct position.|  :x: | :x: | :heavy_check_mark: |  :x: | :x: |

printer_mods/filotto78/6mm_slot_cover/README.md

@@ -0,0 +1,13 @@
+# Cover for extrusion with 6mm slot width
+
+Two simple files.
+One is symmetric and can be used for slots that are inside the printer.
+One isn't symmetric and can be used on external frames, where there are clear panels.
+
+![](./images/symmetric.jpg)
+
+![](./images/one_side.jpg)
+
+![](./images/IMG_3239.jpeg)
+
+![](./images/IMG_3238.jpeg)