Update cfg (#55)

* Update printer.cfg

* Update printer.cfg

* Update printer.cfg

* Update printer.cfg

Chron/SKR 1.3 Config/printer.cfg

@@ -1,7 +1,7 @@
 # CHRONS VORON2 300mm SKR 1.3 TMC2208 UART config
 
 # *** THINGS TO CHANGE/CHECK: ***
-# Arduino paths                         [mcu] section
+# MCU paths                         [mcu] section
 # Thermistor types                      [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
 # FSR switch (z endstop) location       [homing_override] section
 # FSR switch (z endstop) offset for Z0  [stepper_z] section
@@ -110,16 +110,15 @@ endstop_pin: P1.29
 position_min: 0
 position_endstop: 305
 position_max: 305
-homing_speed: 50
+homing_speed: 100
 homing_retract_dist: 5
 homing_positive_dir: true
 
 [tmc2208 stepper_x]
 uart_pin: P1.17
 microsteps: 16
-interpolate: True
+run_current: 1.0
-run_current: 0.8
+hold_current: 0.8
-hold_current: 0.5
 sense_resistor: 0.110
 stealthchop_threshold: 250
 
@@ -133,16 +132,15 @@ endstop_pin: P1.27
 position_min: 0
 position_endstop: 305
 position_max: 305
-homing_speed: 50
+homing_speed: 100
 homing_retract_dist: 5
 homing_positive_dir: true
 
 [tmc2208 stepper_y]
 uart_pin: P1.15
 microsteps: 16
-interpolate: True
+run_current: 1.0
-run_current: 0.8
+hold_current: 0.8
-hold_current: 0.5
 sense_resistor: 0.110
 stealthchop_threshold: 250
  
@@ -157,11 +155,11 @@ step_pin: z:P2.2
 dir_pin: !z:P2.6
 enable_pin: !z:P2.1
 step_distance: 0.00250
-endstop_pin: !z:P1.25
+endstop_pin: z:P1.25
 #   Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
 #   (+) value = endstop above Z0, (-) value = endstop below
 position_endstop: -0.5
-position_max: 240
+position_max: 280
 position_min: -5
 homing_speed: 15.0
 second_homing_speed: 3.0
@@ -170,8 +168,8 @@ homing_retract_dist: 3.0
 [tmc2208 stepper_z]
 uart_pin: z:P1.17
 microsteps: 16
-interpolate: True
+interpolate: False
-run_current: 0.90
+run_current: 1.0
 hold_current: 0.80
 sense_resistor: 0.110
 stealthchop_threshold: 50
@@ -188,8 +186,8 @@ step_distance: 0.00250
 [tmc2208 stepper_z1]
 uart_pin: z:P1.15
 microsteps: 16
-interpolate: True
+interpolate: False
-run_current: 0.80
+run_current: 1.0
 hold_current: 0.80
 sense_resistor: 0.110
 stealthchop_threshold: 50
@@ -205,8 +203,8 @@ step_distance: 0.00250
 [tmc2208 stepper_z2]
 uart_pin: z:P1.10
 microsteps: 16
-interpolate: True
+interpolate: False
-run_current: 0.90
+run_current: 1.0
 hold_current: 0.80
 sense_resistor: 0.110
 stealthchop_threshold: 50
@@ -222,8 +220,8 @@ step_distance: 0.00250
 [tmc2208 stepper_z3]
 uart_pin: z:P1.8
 microsteps: 16
-interpolate: True
+interpolate: False
-run_current: 0.90
+run_current: 1.0
 hold_current: 0.80
 sense_resistor: 0.110
 stealthchop_threshold: 50
@@ -246,7 +244,7 @@ sensor_type: NTC 100K beta 3950
 sensor_pin: P0.24
 smooth_time: 3.0
 min_temp: 10
-max_temp: 270
+max_temp: 300
 max_power: 1.0
 min_extrude_temp: 170
 max_extrude_only_distance: 1150
@@ -254,7 +252,7 @@ max_extrude_cross_section: 9999
 # PA can be disabled by declaring a 0.0 value
 pressure_advance: 0.0
 # time seconds to look ahead for PA moves default is 0.010 or 10ms
-pressure_advance_lookahead_time: 0.010
+#pressure_advance_lookahead_time: 0.010
 control = pid
 pid_kp = 26.213
 pid_ki = 1.304
@@ -264,7 +262,6 @@ pid_kd = 131.721
 [tmc2208 extruder]
 uart_pin: P1.10
 microsteps: 16
-interpolate: True
 run_current: 1.0
 hold_current: 1.0
 sense_resistor: 0.110
@@ -286,7 +283,7 @@ x_offset: 0
 y_offset: 25.0
 z_offset: 0
 #   Speed (in mm/s) of the Z axis when probing. The default is 5mm/s.
-speed: 2.0
+speed: 10.0
 samples: 4
 #   How far to retract (in mm) from the probe point for multi-probe samples
 sample_retract_dist: 3.0
@@ -316,21 +313,20 @@ kick_start_time: 0.5
 cycle_time: 0.001
 
 [heater_fan hotend_fan]
-# Hotend fan MCU Z
 pin: P2.7
-#max_power: 0.8
+max_power: 1.0
-#shutdown_speed: 0.0
+shutdown_speed: 0.0
 kick_start_time: 0.5
 heater: extruder
 heater_temp: 50.0
 #fan_speed: 1.0
 
 #[heater_fan controller_fan]
-# Controller fan HE0 on MCU Z
+# Controller fan
-#pin: z:2.7
+pin: z:P2.7
-#kick_start_time: 0.500
+kick_start_time: 0.500
-#heater: heater_bed
+heater: heater_bed
-#heater_temp: 45.0
+heater_temp: 45.0
 
 [heater_fan exhaust_fan]
 pin: z:P2.4
@@ -349,7 +345,7 @@ sensor_pin: z:P0.25
 smooth_time: 3.0
 max_power: 1.0
 min_temp: 0
-max_temp: 110
+max_temp: 120
 control: pid
 pid_kp: 58.437
 pid_ki: 2.347
@@ -358,9 +354,7 @@ pid_kd: 363.769
 [idle_timeout]
 timeout: 1800
 
-[verify_heater heater_bed]
+
-hysteresis: 0.5
-check_gain_time: 120
 
 [homing_override]
 axes: z
@@ -370,7 +364,7 @@ gcode:
    G0 Z5 F600
    G28 X Y
    #   XY Location of the FSR Switch
-   G0 X99.7 Y305 F3600
+   G0 X202 Y305 F3600 
    G28 Z
    G0 Z10 F1800
    G0 X150 Y150 Z30 F3600
@@ -390,7 +384,7 @@ points:
 	240,60
 	#   The speed (in mm/s) of non-probing moves during the calibration.
 #   The default is 50.
-speed: 50
+speed: 100
 #   The height (in mm) that the head should be commanded to move to
 #   just prior to starting a probe operation. The default is 5
 horizontal_move_z: 10
@@ -410,34 +404,51 @@ speed: 200
 horizontal_move_z: 10
 min_point: 20,20
 max_point: 280,280
-probe_count: 10,10
+probe_count: 5,5
 fade_start: 0.5
 fade_end: 25.0
-split_delta_z: .025
+split_delta_z: .01
-move_check_distance: 5.0
+move_check_distance: 3
 mesh_pps: 0,0
 algorithm: bicubic
+relative_reference_index: 12
 
 
-[display]
+#[display]
 # RepRapDiscount 128x64 Full Graphic Smart Controller
-lcd_type: st7920
+#lcd_type: st7920
-cs_pin: z:P1.19
+#cs_pin: z:P1.19
-sclk_pin: z:P1.20
+#sclk_pin: z:P1.20
-sid_pin: z:P1.18
+#sid_pin: z:P1.18
 #   LCD connector on mcu_z
-menu_timeout: 40
+#menu_timeout: 40
 #   Timeout for menu. Being inactive this amount of seconds will exit the menu
 #   Default is 0 seconds (disabled)
-encoder_pins: ^z:P3.26, ^z:P3.25 
+#encoder_pins: ^z:P3.26, ^z:P3.25 
-click_pin: ^!z:P0.28
+#click_pin: ^!z:P0.28
 #kill_pin: ^!z:
 
+# "mini12864 LCD Display
+#lcd_type: uc1701
+#cs_pin: P1.18
+#a0_pin: P1.19
+#encoder_pins: ^P3.26,^P3.25
+#click_pin: ^!P0.28
+#contrast: 63
+
+#[neopixel my_neopixel]
+#pin: P1.21
+#chain_count: 3
+#initial_RED: 0.1
+#initial_GREEN: 0.5
+#initial_BLUE: 0.0
+
 
 ###   Macros   ###
 
 [gcode_macro G32]
 gcode:
+    BED_MESH_CLEAR
     G28
     QUAD_GANTRY_LEVEL
     G28
@@ -446,11 +457,9 @@ gcode:
 [gcode_macro PRINT_START]
 #   Use PRINT_START for the slicer starting script - please customise for your slicer of choice
 gcode:
-    M117 Homing...                 ; display message
     G28                            ; home all axes
     G1 Z20 F3000                   ; move nozzle away from bed
-    M117 Preheat (Print)           ; display message
+   
-    M104 S0                        ; turn off hotend while waiting for bed to get to temp)
 
 [gcode_macro PRINT_END]
 #   Use PRINT_END for the slicer ending script - please customise for your slicer of choice
@@ -465,7 +474,8 @@ gcode:
     G1 Z2 F3000                    ; move nozzle up 2mm
     G90                            ; absolute positioning
     G0  X125 Y250 F3600            ; park nozzle at rear
-    M117 Finished!
+    BED_MESH_CLEAR
+    
 
 [gcode_macro LOAD_FILAMENT]
 gcode:
@@ -484,6 +494,7 @@ gcode:
 
 [gcode_macro quad_me]
 gcode:
+	BED_MESH_CLEAR
 	G28
 	quad_gantry_level
 	G28
@@ -491,8 +502,7 @@ gcode:
 	G28
 	quad_gantry_level
 	G28
-	G1 X150 Y150 Z20
+	
-
 # Sensor Types
 #   "EPCOS 100K B57560G104F"
 #   "ATC Semitec 104GT-2"