1515ledmod (#518)

* Create README.md

ADXL345 skirt keystone with 2 and 4pin microfit 3.0 connectors. I used what I had laying around.

It's based on alchemyEngine's iteration of the g-code buttons. You can also see how to use it there.
https://github.com/alchemyEngine/EnragedRabbitProject/tree/main/usermods/Skirt-Microfit-Inserts

* Add files via upload

* Create adxl345_skirt_keystone

* Fix skirt keystone

* Update README.md

* Update skirt.keystone.adxl345.jpg

* Update README.md

* Split parts

Update stl's

* Update README.md

Fixed typo's

* Initial commit

* Update README.md

Add zeh new mount to the list

* rename

* yes? no?

bettererer pictures

* Update README.md

Initial description

* Update README.md

Nope. Not a pro at this. It'll work.

* Alphabetical, Biblical, and so on

* Update README.md

Minor wording

* Fix readme

* Update again with correct list

Co-authored-by: KiloQubit <69389593+KiloQubit@users.noreply.github.com>

printer_mods/Jon/1515_led_mount/README.md

@@ -0,0 +1,43 @@
+# Snap in 1515 LED mount for WS2812B led strips.
+<img src="IMG/print_finish.gif">
+
+BOM:
+- [WS2812BECO Black PCB - 5m 30 IP30](https://www.aliexpress.com/item/2036819167.html "aba")
+- Some cables
+- A soldering iron
+- JST-XH Crimps
+
+
+Print guide:
+
+Print 9 normal and 9 mirrored.
+I mixed 16 and 17mm because the spacing on these are not exactly what you'd call accurate.
+
+
+Preparation:
+
+I use 4 led's on each side. Solder the cables and add some heatshrink wrap the end. Probably a good idea to test and configure them first too, so you don't have to take it out again after you've mounted it.
+
+
+Mounting:
+
+Push one in, then slide the led strip into it and keep things in the back. Then keep adding one and one until finished. Et voila. Slide the cable over the back panel and into the electronics bay. Wire them in parallel and put them into the BTT SKR Mini E3 V2 neopixel slot.
+<img src="IMG/wiring.jpg" width="250" height="250">
+
+
+Klipper config:
+
+```
+[neopixel case_lights]
+##  Chamber Lighting - In 5V-RGB Position
+pin: PA8
+chain_count: 4
+initial_RED: 0
+initial_GREEN: 0
+initial_BLUE: 1
+```
+
+<img src="IMG/led_strip.jpg" width="825" height="461">
+
+
+If this looks familiar contact me so i can credit you. This is based on some other 1515 mount. I just remade the rest. Heavily based on eddie's misumi holders.

printer_mods/README.md

@@ -162,7 +162,8 @@ like so:
 | | [Mid Panel](./JNP/Mid-Panel)| Panel for SKR1.4/1.4 or SKR E3 mini mount | :heavy_check_mark: |:x: |:x: |:x: |
 | | [Neopixel Case](./JNP/Neopixel-Y_Rails) | mounting for Neopixel strip with 8 LED´s | :heavy_check_mark: |:x: |:x: |:x: |
 | | [Side Panels](./JNP/Side-Panels) | Panels with intergrated hinge | :heavy_check_mark: |:x: |:x: |:x: |
-| Jon | [adxl345 skirt keystone](./Jon/adxl345_skirt_keystone) | Skirt keystone for ADXL345 using Microfit 3.0 | :x: | :x: | :heavy_check_mark: | :grey_question: | :grey_question: | :heavy_check_mark: |
+| Jon | [1515 LED Mount](./Jon/1515_led_mount) | Snap in 1515 Led mount for WS2812B |:heavy_check_mark:|:x:|:x:|:x:|:x:|
+| | [adxl345 skirt keystone](./Jon/adxl345_skirt_keystone) | Skirt keystone for ADXL345 using Microfit 3.0 | :x: | :x: | :heavy_check_mark: | :grey_question: | :grey_question: |
 | joposter | [V0 Clippable LED Caselight](./joposter/v0_clippable_ledmounts) | LED Case light for the V0 that clips into the extrusions | :heavy_check_mark: | :x: | :x: | :x: | :x: |
 | JosAr | [Klicky Probe](./JosAr/Klicky-Probe) | Microswitch based inductive probe replacement | :x: | :heavy_check_mark: |:heavy_check_mark: | :x: | :heavy_check_mark: |
 | KageUrufu | [Euclid Probe Carriage](./kageurufu/mgn12-euclid) | A MGN-12 carriage with an inset mount for a Euclid Probe | :x: | :heavy_check_mark: | :heavy_check_mark: | :grey_question: | :heavy_check_mark: |