Slitte mods (#750)

* Create file.txt

* Create test.txt

* Create readme.md

* Create readme.md

* Update readme.md

* Create readme.md

* Add files via upload

* Create readme.md

* Add files via upload

* Add files via upload

* Update readme.md

* Update readme.md

* Create readme.md

* Add files via upload

* Delete file.txt

* Create licence

* Create licence.md

* Create readme.md

* Add files via upload

* Delete test.txt

* Create readme.md

* Update readme.md

* Create readme.md

* Add files via upload

* Update readme.md

* Update README.md

* Delete licence.md

* Delete licence

* Update readme.md

* Update readme.md

* Delete readme.md

* Delete readme.md

* Delete readme.md

* Delete readme.md

* Delete readme.md

* Delete readme.md

* Update readme.md

* Update readme.md

* Delete ssd_bracket.STL

* Create readme.md

* Add files via upload

* Delete readme.md

printer_mods/README.md

@@ -345,6 +345,8 @@ like so:
 | Shteeeeeve | [V0.1 LED Tophat](./Shteeeeeve/V01-LED-Tophat) | V0.1 LED Tophat w/ 24V LED Lightstrip | :heavy_check_mark: | :x: | :x: | :x: |
 | Slidr | [PanzerBalls 2.4](./Slidr/PanzerBalls2.4) | Squash Ball Feet for V2.4 | :x: | :x: | :heavy_check_mark: |:x:| :x: |
 | | [PanzerChain 2.4](./Slidr/PanzerChain2.4) | Energychain for V2.4 | :x: | :x: | :heavy_check_mark: |:x:| :x: |
+| slitte | [PCB_Probe](./slitte/PCB_Probe) | PCB for BAT85 and pull up resistor | :x: | :x: | :heavy_check_mark: | :x: | :heavy_check_mark: |
+|  | [ssd_bracket](./slitte/ssd_bracket) | bracket for mounting a 2.5" ssd to a din rail | :x: | :x: | :heavy_check_mark: | :x: | :heavy_check_mark: |
 |sloscotty|[Switchwire Wall Plate](./sloscotty/SW_Wall_Plate)|SW plate for enclosure|:x:|:x:|:x:|:heavy_check_mark:|
 | | [NoNutz TopHat Cam Extension](./sloscotty/TopHat_Cam_Extension) | Tophat extension with integrated webcam for V0/0.1 | :heavy_check_mark: | :x: | :x: | :x: | :x: |
 | spacelab2021 | [Orbiter Clockwork Mount](spacelab2021/Orbiter-Clockwork) | A clockwork adaptor for the Orbiter v1.5 Extruder with full integration into the Afterburner. Includes a filament quick release lever for simple filament loading and unloading. | :x: | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: | :heavy_check_mark: |

printer_mods/slitte/PCB_Probe/readme.md

@@ -0,0 +1,33 @@
+# PCB_Probe
+
+
+
+
+Short discription: This PCB can be mounted on the DIN Rail under a Voron 3D printer. There are two ways of wiring the Omron inductive probe to the BTT Octopus V1.1 mainbord. Either you wire the probe directly to the dedicated probe port of the Octopus, or you wire the probe to an Endstop Port(DIAG_7).
+For both ways you need additional components to run the probe properly. 
+
+In case you decide for the dedicated probe port, you need a 4k7 Ohm pull up resistor between the signal to +24V. Just solder the THT 4k7 pull up resistor on it's place and set the jumper to "w/o BAT85". This bridges the diode. You can leave the space for the diode empty.
+
+
+For the official recommended way to wire the probe to DIAG_7 port, a BAT85 diode is needed to prevent the mainboard from damage. Just solder the BAT85 in it's place and set the jumper to "w BAT85". When using this configuration, you must leave the pull-up resistor out. 
+
+
+It's compatible with the Voron Trident and V2.4. If you use the Toolhead PCB by hardk, you may not need this PCB because the Toolhead pcb got a BAT85 diode already.
+
+The following part has to be printed x1: [pcb_din_clip_x3](https://github.com/VoronDesign/Voron-2/blob/eb094399681bcac4efce723157b8638c69173cb3/STLs/Electronics_Bay/pcb_din_clip_x3.stl)
+
+
+BOM:
+
+- 1x PCB_Probe
+- 2x M2x10 self tapping screws
+- 2x JST B3B-XH-A
+- 1x BAT85 or 1x 4k7 Ohm Restistor (depending on the way you want to wire the probe)
+- 1x pcb_din_clip
+- 1x 2 pin jumper bridge
+- 1x 3 pin pin-header 2,54mm
+
+
+
+!!!Attention!! 
+the images show the Prototype state of the project and doesn't include the Pull Up resistor mount. Used probe: Omron TL-Q5MC2-Z

printer_mods/slitte/ssd_bracket/readme.md

@@ -0,0 +1,21 @@
+# ssd_bracket
+bracket to mount a ssd-drive to the din rail under a voron printer
+
+This bracket is designed to mount a ssd drive in the electronic bay of a voron 2.4 or Trident. 
+
+The following part has to be printed x1: [pcb_din_clip_x3](https://github.com/VoronDesign/Voron-2/blob/eb094399681bcac4efce723157b8638c69173cb3/STLs/Electronics_Bay/pcb_din_clip_x3.stl)
+
+
+Bom:
+
+- 1x ssd_bracket
+- 1x pcb_din_clip
+- 2x M2x10 self tapping screw
+- 4x M3x12 SHCS
+
+Instructions:
+
+Use the M2x10 self tapping screws to mount the ssd_bracket to the pcb_din_clip. Then mount your ssd drive with the M3x12 SHCS to the ssd_bracket. Then snap the assembly in place on the din rail. It mounts similar to the Raspberry Pi on page 178 to 179 on the Voron 2.4r2 manual. 
+
+
+